Search results for query: *

Thanks for the feedback. Its a did number to a ldn at the console. If possible the goal is have the ldn remain on the console.

I have a Meridian 11c 2250 console. A small group of sales people use a number to call our office which rings through to a button on the 2250 console. This telephone number is different from our main published number. I want the calls from the sales group to forward to a different extension if...

I've set both Answer and Disconnect supervision to on. I did not notice any change in the amount of time to release the line when the called party hangs up. Im still waiting 10-15 sec. before the TAPI programs senses the line is dropped. Any other suggestions?

It is happening on all stations running the TAPI programs. I have delays up to 15 secs before the line is released and the screen pop appears at the PC. I reviewed all settings at the phone and program and all is normal. If the call is dropped from my end by just hanging up the phone the screen...

Im using a TAPI screen pop at my PC when a call is ended. It is triggered when the called party hangs up the phone and the phone system detects the call is over. There seems to be a delay detecting when the actual call is over. Is there a setting within the Definity G3Si that will immediately...

The individual reported another series of messages in their voicemail. I'll try the "display activity" and see what it reports. I want to try to avoid having to purchase additional product just to find the source. If this can be done with the items that I already have it would be perfect. I will...

I have a Definity G3si R8 and an Intuity Audix voicemail. One of my users is concerned over the number of crank/harassing calls left in their voicemail. The calls never ring at the handset only a message is left in the voicemail. I do not have a call accounting package installed on the system...

Ok. I am now at a point where I can place outbound calls from a station on the IP Office via Definity trunk. I do have an issue where I have to press 9 twice to get the outbound dial tone. My ultimate goal is have the stations on the IP office act the same as those on the Definity. Stations on...

I already had it configured that way. I do not have any local trunks on the IP Office all trunks are configured on the Definity. I can dial stations on the Definity but cannot place an outbound call from the IP Office.

Not sure if I should have continued my previous thread but I started a new one. I've connected my IP office 403 to My Definity G3si R8 via the T1 interface of the IP Office to a T1 card in the Definity. I am able to reach stations attached to the Definity. My plan is to get dial tone from the...

You're right the QSIG license is to dear. I'll take your tip and look at using ETSI. Its good to know that I have options. Many thanks for the advice!

I have an IP Office 403 with PRI interface. I need to connect this to an Avaya Definity G3Si R8 PBX. Both units sit in the same room side by side. I have a spare T1 circuit pack inside the Definity to use for this project. The only thing I need to do is get dial tone on the IP Office from the...

My internet T1 terminates at the internal csu of my 3725 router. I have a firewall/vpn concentrator (not Cisco) between the router and my LAN. I have several branch office VPN tunnels terminating at the vpn concentrator. Each branch office has a static IP. I want to limit each VPN tunnel a...

Thanks so much for the prompt response. Ok with the CLAN card to get the Definity on the network. Is my release of 8.3 sufficient to work with the softphone. Will I still be able to purchase the softphone product and expect it to work with this release?

I have a Definity G3si ver8.3. I've been pulled in many directions with IP softphone that I am not sure which is fact anymore. I have a software dialer which I intend to use for a group of users. I was told from the dialers manufacturer that I could use the IP softphone for call control to a...

I have BE9.0 for Windows and want to backup a Novell folder. I know I can use the Netware agent to backup Novell servers but what of the open files. Will the Netware agent backup the open files or do I need the open files option as well? If I need the OFO is it the Novell OFO or the Windows OFO...