Recent content by roupe

WE have some large customers who route their 911 calls to their Security Dept With ESA (Emergency Services Access) software the 911 dialed digits can be sent to another dn in the pbx. If the cust wants to send the 911 calls to the PSAP then a key on a set can flash and signal the owner that...

You must add NDS (name delivery service) to the recap prompt on the d chan. Disabling the d chan does not take down the pri just prevents new in/out calls until d chan is reenable in LD 96

Close as I can get If you are sending the LD 95 name to the public network along with the clid then your pri has the feature Name Delivery Usually set up to only receive the name and clid of public caller, but if cls of set as described below, then network would pass your Ld 95 name. The...

trvlr1 is correct If 2 calls hit at once, the second call is given busy treatment. Only so with MCR Probably why a few go to mail.

IVJOE Do what I recommend to all my customers Tell the network folks to keep their 9xxx and 0xxx numbers. They love to sell those if they can Nobody with a pbx wants them for dids. You said only a handful Maybe this will work for you

You said some of the calls? Are all of the calls incoming and are the trunks pri? Do the calls come in then back out on the same trunk route?

If the trunk route is route 1-19 make sure the console operator monitors the trunk group keys on the left side of the 2250 console. The 10 keys are routes 0-9 press SHIFT to see the next 10. If it is programmed as page trunk, when operator presses loop key then page key, she takes control of...

Change the key to voice call and target the dn on the set that the hot d was pointed at. As long as the dn the voice call is pointed at is single app and is always idle the caller will not hear ringback tone. If handsfree the caller just presses the key The called party replys handsfree

In LD 50 CPTM call park timer in seconds 30-240 PRT CPK in LD 50 to see what yours is set at and change the CPTM to increase/decrease

Directory Number Expansion (DNXP) package 150 is required This feature increases the number of digits allowed for internal Directory Numbers (DNs), from a maximum of four digits per DN to seven digits per DN. The following internal DNs have been expanded: • Single-line telephone DNs •...

sporty2 is correct When our first pri with clid went in in 1990 the co would send whatever you sent from the switch. Every pri I have implemented for my customers in the past 10 years is screened by the CO so that an incorrect or someone else's number is not being sent. When the clid feature...

Your local trunks are provisioned as PRI you said. Therefore the T1 serving those local trunks is provisioned as ISDN with CLID capability(incoming and outgoing) The T1 from your ld carrier is programmed as standard dti (digital trunk interface) that uses fas signaling (facility associated)...

go to Ld 21 and at REQ enter PRT at TYPE enter CDR and cr until cdr data is printed. If cdr is not set as yes go into ld 15 at REQ enter CHG at type enter CDR at CDR prompt enter YES When you got to LD 16 chg RDB CDR YES In ld 17 CHG ADAN then cr at ADAN prompt enter CHG TTY @ cr...

TM 3.1 when set up correctly is a good product. I installed it on one of my customer's system in Mobile last week. The IT guy that is using it also has a good working knowledge of the cli on the maint terminal. TM 3.1 is for users that have a "working" knowledge of the Nortel database...

The T1 is the facility (circuit) your trunks work on. Those digital trunks can be provisioned by your local or ld carrier as isdn pri trunks providing in or outbound calls on any of the channels. If the ld t1 is not isdn pri then no caller id info is passed/received. Ask the ld carrier what...