Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by canopus

  1. canopus

    Server sent disconnect message type 11 (by application)

    I cannot login via ssh to my CS1000 nor via Web. I just changed a Distant Steering Code this morning. Any ideas?
  2. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    I need to send 10 digits to the other side but it is just sending 8 digits after the access code Im dialing in nortel side 88 NXX NXX XXXX And the nortel is stripping two digits 88 NXX NXX XX 88 809 220 11 Any idea?
  3. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    I just sending 8 digits to the asterisk side. Any help My route access code is 88
  4. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    I have created a new DSC 88 to reach that route. REQ prt CUST 0 FEAT cdp TYPE dsc DSC DSC 1896 FLEN 0 DSP LSC RRPA NO RLI 5 CCBA NO NPA NXX DSC 506 FLEN 0 DSP LSC RRPA NO RLI 4 CCBA NO NPA NXX DSC 88 FLEN 0 DSP LSC RRPA NO RLI 5 CCBA NO NPA NXX Im dialing out to the asterisk side...
  5. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    All incoming calls are working very well. I have a IVR working with this route, all DIGITS NXXX are working well. Only Outgoing calls are not working with 6000 ACOD
  6. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    I did it but it still fast busy. Any ideas?
  7. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    The result is: >ld 21 PT1000 REQ: prt TYPE: rdb CUST 0 ROUT 10 TYPE RDB CUST 00 ROUT 10 DES ASTERISK_VOIP TKTP TIE M911P NO ESN NO RPA NO CNVT NO SAT NO RCLS INT VTRK NO NODE DTRK YES BRIP NO DGTP PRI ISDN YES MODE PRA IFC ESS5 SBN NO PNI 00001 SRVC NNSF NCNA...
  8. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    Now one only thing: How to assign an access code for this trunk from the CS1K side? Im having circuit busy in the Nortel. Any help?
  9. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    I have done this: ld 96 .dis tmdi 004 0 03 all .enl tdmi 004 0 03 OK . Everything went Ok until today. In an aport to the community, I have to say this: When you make any change in the Asterisk box,using the web browser, You will have circuit busy. To fix this, just type this two commands...
  10. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    HUMMMMMM, something weird.... My another DLOP went DSBL. >ld 60 DTI000 .stat DTI TRK LOOP 100 - ENBL FFMT/LCMT/YALMT: D4/ AMI/DG2 TRACKING SERVICE RESTORE: YES YEL ALM PROCESS: YES ALARM STATUS : RED CH 01 - IDLE DID VCE CH 02 - DSBL DID VCE CH 03 - DSBL DID VCE...
  11. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    Everything is working good! Thanks for your help!
  12. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    SPAN 1 IN ALARM (YELLOW) pri show span 1 Primary D-channel: 24 Status: In Alarm, Up, Active Switchtype: Lucent 5E Type: Network Remote type: Unknown node type Overlap Dial: 0 Logical Channel Mapping: 0 Timer and counter settings: N200: 3 N202: 3 K: 7 T200: 1000 T201: 1000 T202...
  13. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    Good shot! I rebuilded the crossover and PUM! The TMDI Card went green.... Now I have YELLOW alarm in the asterisk side.... Maybe clocking issues?
  14. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    I forced to enable the bchannels. Now they appear like this: >ld 60 DTI000 .stat 101 PRI* TRK LOOP 101 - ENBL FFMT/LCMT/YALMT: ESF/B8Z/FDL SERVICE RESTORE: YES YEL ALM PROCESS: YES ALARM STATUS : RED CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE VOD * CH 03 - IDLE TIE VOD *...
  15. canopus

    How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

    I was suspecting the same... Let me try...
See more

Part and Inventory Search

Back
Top