How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

[canopus]

Hi, I'm working on this trunk but I have this issue enabling the bchannels.

What I need to do to enable it?

ld 96

.enl 101


Any Help?

 

[canopus]

I have done this:

ld 96
.dis tmdi 004 0 03 all

.enl tdmi 004 0 03
OK
.


Everything went Ok until today.

In an aport to the community, I have to say this:

When you make any change in the Asterisk box,using the web browser, You will have circuit busy. To fix this, just type this two commands in the cli:

asterisk CLI> dahdi restart
asterisk CLI> pri intense debug span 1


everything will run as a top model in the pasarella!

Than you for your kind help!

 

[KCFLHRC]

You should probably force download the TMDI

 

[canopus]

Now one only thing:

How to assign an access code for this trunk from the CS1K side?

Im having circuit busy in the Nortel.

Any help?

 

[KCFLHRC]

When you built your route you assigned an access code.

 

[bhassell2000]

prt
rdb
look for ACOD

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[canopus]

The result is:


>ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 10

TYPE RDB
CUST 00
ROUT 10
DES ASTERISK_VOIP
TKTP TIE
M911P NO
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS INT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ESS5
SBN NO
PNI 00001
SRVC NNSF
NCNA YES
NCRD YES
CHTY BCH
CTYP UKWN
INAC YES
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 6000
TCPP NO
PII NO
TARG 01
CLEN 10
BILN NO
OABS
INST
ANTK
SIGO STD
MFC NO
ICIS YES
OGIS YES
PTUT 0
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896


PAGE 002

SFB 3
NBS 2048
NBL 4096
TFD 0
DTD NO
SCDT NO
2 DT NO
DRNG NO
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
MUS NO
PANS YES
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
OPR NO
ALRM NO
ART 0
TIDY 6000 10
SGRP 0
CCBA NO
ARDN NO
AACR NO

REQ:
REQ PRT
TYPE:
TYPE RDB
CUST ***
OVL000
>ld 21
PT1000

REQ: ltm
CUST 0
ROUT 10

TYPE TLST
TKTP TIE
ROUT 10
DES ASTERISK_VOIP
TN 101 01 MBER 1 ASTERISK_VOIPK
TN 101 02 MBER 2 ASTERISK_VOIPK
TN 101 03 MBER 3 ASTERISK_VOIPK
TN 101 04 MBER 4 ASTERISK_VOIPK
TN 101 05 MBER 5 ASTERISK_VOIPK
TN 101 06 MBER 6 ASTERISK_VOIPK
TN 101 07 MBER 7 ASTERISK_VOIPK
TN 101 08 MBER 8 ASTERISK_VOIPK
TN 101 09 MBER 9 ASTERISK_VOIPK
TN 101 10 MBER 10 ASTERISK_VOIPK
TN 101 11 MBER 11 ASTERISK_VOIPK
TN 101 12 MBER 12 ASTERISK_VOIPK
TN 101 13 MBER 13 ASTERISK_VOIPK
TN 101 14 MBER 14 ASTERISK_VOIPK
TN 101 15 MBER 15 ASTERISK_VOIPK
TN 101 16 MBER 16 ASTERISK_VOIPK
TN 101 17 MBER 17 ASTERISK_VOIPK
TN 101 18 MBER 18 ASTERISK_VOIPK
TN 101 19 MBER 19 ASTERISK_VOIPK
TN 101 20 MBER 20 ASTERISK_VOIPK
TN 101 21 MBER 21 ASTERISK_VOIPK
TN 101 22 MBER 22 ASTERISK_VOIPK
TN 101 23 MBER 23 ASTERISK_VOIPK


The access code is 6000 but when I try 6000NPANXXXXXX is not working. The RLI made for this trunk is RLI 5.

How can I fix this?

 

[KCFLHRC]

What happens if you just dial 6000? Do you get a fast busy? If so then remove the TARG from the route or make the TGAR on your test phone 0

 

[canopus]

I did it but it still fast busy.

Any ideas?

 

[KCFLHRC]

My guess is the Nortel and Asterisk are still not synced up properly. Look at your channels again in LD 60 and stat your D-Channel in LD 96.

 

[canopus]

All incoming calls are working very well. I have a IVR working with this route, all DIGITS NXXX are working well.

Only Outgoing calls are not working with 6000 ACOD

 

[janaya]

why don't you set up TSC (trunk steering codes) to dial from the Nortel to the Asterisk? Then you don't have to worry about dialing the Access Code.


LD 86
Create a new DGT. You don't have to insert or delete any digits, just set CTYP to NCHG

LD 86
Create new RLB. Make sure you point this to your route and put in the DGT

LD 87
Create a new TSC that points to the RLB you make.

Now you can just call the number on the Asterisk.

or you could start with removing the TARG on the Asterisk route to ensure that there are no restrictions to dial the ACOD.

John Anaya
Signet6 Network Sciences
ACSS/ACIS - CS1000 Rls 7.5/Call Pilot 5
ACSS/ACIS - SME - IP Office 8.0
APSS/APDS - Avaya UC Services

Public Profile

http://www.linkedin.com/pub/john-anaya/25/1b9/a9b/Edit

 

[janaya]

Or you could use a maintenance set to direct select the trunk and call. This will tell you if the calll path is correct and then you know its settings in the Nortel....i mean Avaya

John Anaya
Signet6 Network Sciences
ACSS/ACIS - CS1000 Rls 7.5/Call Pilot 5
ACSS/ACIS - SME - IP Office 8.0
APSS/APDS - Avaya UC Services

Public Profile

http://www.linkedin.com/pub/john-anaya/25/1b9/a9b/Edit

 

[canopus]

I have created a new DSC 88 to reach that route.

REQ prt
CUST 0
FEAT cdp
TYPE dsc
DSC
DSC 1896
FLEN 0
DSP LSC
RRPA NO
RLI 5
CCBA NO
NPA
NXX
DSC 506
FLEN 0
DSP LSC
RRPA NO
RLI 4
CCBA NO
NPA
NXX
DSC 88
FLEN 0
DSP LSC
RRPA NO
RLI 5
CCBA NO
NPA
NXX


Im dialing out to the asterisk side successfully, but the issue is with the digits longitude.

Im receiving this in the asterisk side:


PRI Span: 1 > 0 bytes of data
PRI Span: 1 Done handling message for SAPI/TEI=0/0
Span 1: Processing event PRI_EVENT_RING
-- Span 1: Extension 8880922011@default does not exist. Rejecting call from '3325'.
PRI Span: 1 q931.c:6837 q931_hangup: Hangup other cref:23
PRI Span: 1 q931.c:6594 __q931_hangup: ourstate Call Present, peerstate Call Initiated, hold-state Idle
PRI Span: 1 q931.c:6085 q931_release_complete: Call 23 enters state 0 (Null). Hold state: Idle


How can I increase the digits longitude to be passed to the other side?

 

[canopus]

I just sending 8 digits to the asterisk side.

Any help

My route access code is 88

 

[janaya]

What do you need to see from the Asterisk side? What number are you trying to reach? Not what are you dialing.

Example:

Nortel Extension 1234 is trying to dial Asterisk Extension 5678.

John Anaya
Signet6 Network Sciences
ACSS/ACIS - CS1000 Rls 7.5/Call Pilot 5
ACSS/ACIS - SME - IP Office 8.0
APSS/APDS - Avaya UC Services

Public Profile

http://www.linkedin.com/pub/john-anaya/25/1b9/a9b/Edit

 

[canopus]

I need to send 10 digits to the other side but it is just sending 8 digits after the access code
Im dialing in nortel side

88 NXX NXX XXXX

And the nortel is stripping two digits
88 NXX NXX XX

88 809 220 11

Any idea?

 

[bhassell2000]

is there a DMI being used that is stripping digits?

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[janaya]

So you need to dial;

8880922011 - this is the number on the Asterisk that you are trying to reach?

go to LD 96

.enl msgi XX (XX is the dchannel number on the loop)
.enl msgi XX (XX is the dchannel number on the loop)

Make a test call and post what happens here. This is a dchannel trace and will show us what is being pulsed out.

To turn this off

LD 96

.dis msgi XX
.dis msgo XX

But post your information here.



John Anaya
Signet6 Network Sciences
ACSS/ACIS - CS1000 Rls 7.5/Call Pilot 5
ACSS/ACIS - SME - IP Office 8.0
APSS/APDS - Avaya UC Services

Public Profile

http://www.linkedin.com/pub/john-anaya/25/1b9/a9b/Edit

 

[KCFLHRC]

Make sure the CLS on your phone is UNR