Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

Status
Not open for further replies.

canopus

Programmer
Joined
Feb 23, 2013
Messages
31
Location
DO
Hi, I'm working on this trunk but I have this issue enabling the bchannels.

What I need to do to enable it?

ld 96

.enl 101


Any Help?
 
In your subject you say "D4 AMI"; you can't have a PRI with these T1 parameters; needs to be B8S ESF to get 64k channels.
 
Ok I just changed this parameters, Now I have to build a Coordinated Dialplan to reach this route...


What stands for local steering code?

Help
 
BCHANNELS ARE NOT enabling!

.enl 101

DTI003

.enll 101

DTI022 101

.stat 101

PRI* TRK LOOP 101 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : RED
CH 01 - DSBL TIE VOD * CH 02 - DSBL TIE VOD *
CH 03 - DSBL TIE VOD * CH 04 - DSBL TIE VOD *
CH 05 - DSBL TIE VOD * CH 06 - DSBL TIE VOD *
CH 07 - DSBL TIE VOD * CH 08 - DSBL TIE VOD *
CH 09 - DSBL TIE VOD * CH 10 - DSBL TIE VOD *
CH 11 - DSBL TIE VOD * CH 12 - DSBL TIE VOD *
CH 13 - DSBL TIE VOD * CH 14 - DSBL TIE VOD *
CH 15 - DSBL TIE VOD * CH 16 - DSBL TIE VOD *
CH 17 - DSBL TIE VOD * CH 18 - DSBL TIE VOD *
CH 19 - DSBL TIE VOD * CH 20 - DSBL TIE VOD *
CH 21 - DSBL TIE VOD * CH 22 - DSBL TIE VOD *
CH 23 - DSBL TIE VOD * CH 24 - DCH 10

What I need to do?
 
Your T-1 is in RED Alarm, it will never come up that way.
 
You need to connect it to what ever equipment this T-1 is for and if that end is ready then the T-1 will come out of RED Alarm.
 
The PRI T-1 is in red alarm - there's no signal making it to the card (ALARM STATUS : RED). It will never come up until you fix this physical layer issue.
 
I have an asterisk box at the far end. The DCH 10 is OPER but the BCHANNELS appears DISL
 
You have to get rid of the RED Alarm before anything will work
 
You may need a cross over cable to swap pins 1/2 and 4/5
 
I was suspecting the same... Let me try...
 
I forced to enable the bchannels. Now they appear like this:

>ld 60
DTI000
.stat 101

PRI* TRK LOOP 101 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : RED
CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE VOD *
CH 03 - IDLE TIE VOD * CH 04 - IDLE TIE VOD *
CH 05 - IDLE TIE VOD * CH 06 - IDLE TIE VOD *
CH 07 - IDLE TIE VOD * CH 08 - IDLE TIE VOD *
CH 09 - IDLE TIE VOD * CH 10 - IDLE TIE VOD *
CH 11 - IDLE TIE VOD * CH 12 - IDLE TIE VOD *
CH 13 - IDLE TIE VOD * CH 14 - IDLE TIE VOD *
CH 15 - IDLE TIE VOD * CH 16 - IDLE TIE VOD *
CH 17 - IDLE TIE VOD * CH 18 - IDLE TIE VOD *
CH 19 - IDLE TIE VOD * CH 20 - IDLE TIE VOD *
CH 21 - IDLE TIE VOD * CH 22 - IDLE TIE VOD *
CH 23 - IDLE TIE VOD * CH 24 - DCH 10
.


The red alarm seems to be in the physical layer.

I will remake the T1 crossover.


I ´ll let U know
 
Good shot!

I rebuilded the crossover and PUM!

The TMDI Card went green....

Now I have YELLOW alarm in the asterisk side....


Maybe clocking issues?
 
SPAN 1 IN ALARM (YELLOW)
pri show span 1
Primary D-channel: 24
Status: In Alarm, Up, Active
Switchtype: Lucent 5E
Type: Network
Remote type: Unknown node type
Overlap Dial: 0
Logical Channel Mapping: 0
Timer and counter settings:
N200: 3
N202: 3
K: 7
T200: 1000
T201: 1000
T202: 10000
T203: 10000
T303: 4000
T305: 30000
T308: 4000
T309: 6000
T312: 6000
T313: 4000
T-HOLD: 4000
T-RETRIEVE: 4000
T-RESPONSE: 4000
Q931 RX: 0
Q931 TX: 0
Q921 RX: 20
Q921 TX: 21
Q921 Outstanding: 0 (TEI=0)
Total active-calls:0 global:0
CC records:
Overlap Recv: No
 
Everything is working good!

Thanks for your help!
 
HUMMMMMM, something weird....

My another DLOP went DSBL.

>ld 60
DTI000
.stat

DTI TRK LOOP 100 - ENBL
FFMT/LCMT/YALMT: D4/ AMI/DG2
TRACKING
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : RED
CH 01 - IDLE DID VCE CH 02 - DSBL DID VCE
CH 03 - DSBL DID VCE CH 04 - DSBL DID VCE
CH 05 - DSBL DID VCE CH 06 - DSBL DID VCE
CH 07 - DSBL DID VCE CH 08 - DSBL DID VCE
CH 09 - DSBL DID VCE CH 10 - DSBL DID VCE
CH 11 - DSBL DID VCE CH 12 - DSBL DID VCE
CH 13 - DSBL DID VCE CH 14 - DSBL DID VCE
CH 15 - DSBL DID VCE CH 16 - DSBL DID VCE
CH 17 - DSBL DID VCE CH 18 - DSBL DID VCE
CH 19 - DSBL DID VCE CH 20 - DSBL DID VCE
CH 21 - DSBL DID VCE CH 22 - DSBL DID VCE
CH 23 - DSBL DID VCE CH 24 - DSBL DID VCE

PRI* TRK LOOP 101 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE VOD *
CH 03 - IDLE TIE VOD * CH 04 - IDLE TIE VOD *
CH 05 - IDLE TIE VOD * CH 06 - IDLE TIE VOD *
CH 07 - IDLE TIE VOD * CH 08 - IDLE TIE VOD *
CH 09 - IDLE TIE VOD * CH 10 - IDLE TIE VOD *
CH 11 - IDLE TIE VOD * CH 12 - IDLE TIE VOD *
CH 13 - IDLE TIE VOD * CH 14 - IDLE TIE VOD *
CH 15 - IDLE TIE VOD * CH 16 - IDLE TIE VOD *
CH 17 - IDLE TIE VOD * CH 18 - IDLE TIE VOD *
CH 19 - IDLE TIE VOD * CH 20 - IDLE TIE VOD *
CH 21 - IDLE TIE VOD * CH 22 - IDLE TIE VOD *
CH 23 - IDLE TIE VOD * CH 24 - DCH 10

any idea?
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top