How To Enable BCHANNELS after enable DCH? PRI ESS5 D4 AMI

[canopus]

Hi, I'm working on this trunk but I have this issue enabling the bchannels.

What I need to do to enable it?

ld 96

.enl 101


Any Help?

 

[bhassell2000]

ld 60
enl (loop Number)

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[curtismo]

In your subject you say "D4 AMI"; you can't have a PRI with these T1 parameters; needs to be B8S ESF to get 64k channels.

 

[canopus]

Ok I just changed this parameters, Now I have to build a Coordinated Dialplan to reach this route...


What stands for local steering code?

Help

 

[canopus]

BCHANNELS ARE NOT enabling!

.enl 101

DTI003

.enll 101

DTI022 101

.stat 101

PRI* TRK LOOP 101 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : RED
CH 01 - DSBL TIE VOD * CH 02 - DSBL TIE VOD *
CH 03 - DSBL TIE VOD * CH 04 - DSBL TIE VOD *
CH 05 - DSBL TIE VOD * CH 06 - DSBL TIE VOD *
CH 07 - DSBL TIE VOD * CH 08 - DSBL TIE VOD *
CH 09 - DSBL TIE VOD * CH 10 - DSBL TIE VOD *
CH 11 - DSBL TIE VOD * CH 12 - DSBL TIE VOD *
CH 13 - DSBL TIE VOD * CH 14 - DSBL TIE VOD *
CH 15 - DSBL TIE VOD * CH 16 - DSBL TIE VOD *
CH 17 - DSBL TIE VOD * CH 18 - DSBL TIE VOD *
CH 19 - DSBL TIE VOD * CH 20 - DSBL TIE VOD *
CH 21 - DSBL TIE VOD * CH 22 - DSBL TIE VOD *
CH 23 - DSBL TIE VOD * CH 24 - DCH 10

What I need to do?

 

[KCFLHRC]

Your T-1 is in RED Alarm, it will never come up that way.

 

[canopus]

Ok what I did wrong?

 

[KCFLHRC]

You need to connect it to what ever equipment this T-1 is for and if that end is ready then the T-1 will come out of RED Alarm.

 

[curtismo]

The PRI T-1 is in red alarm - there's no signal making it to the card (ALARM STATUS : RED). It will never come up until you fix this physical layer issue.

 

[canopus]

I have an asterisk box at the far end. The DCH 10 is OPER but the BCHANNELS appears DISL

 

[KCFLHRC]

You have to get rid of the RED Alarm before anything will work

 

[canopus]

Any suggests?

 

[KCFLHRC]

You may need a cross over cable to swap pins 1/2 and 4/5

 

[canopus]

I was suspecting the same... Let me try...

 

[canopus]

I forced to enable the bchannels. Now they appear like this:

>ld 60
DTI000
.stat 101

PRI* TRK LOOP 101 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : RED
CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE VOD *
CH 03 - IDLE TIE VOD * CH 04 - IDLE TIE VOD *
CH 05 - IDLE TIE VOD * CH 06 - IDLE TIE VOD *
CH 07 - IDLE TIE VOD * CH 08 - IDLE TIE VOD *
CH 09 - IDLE TIE VOD * CH 10 - IDLE TIE VOD *
CH 11 - IDLE TIE VOD * CH 12 - IDLE TIE VOD *
CH 13 - IDLE TIE VOD * CH 14 - IDLE TIE VOD *
CH 15 - IDLE TIE VOD * CH 16 - IDLE TIE VOD *
CH 17 - IDLE TIE VOD * CH 18 - IDLE TIE VOD *
CH 19 - IDLE TIE VOD * CH 20 - IDLE TIE VOD *
CH 21 - IDLE TIE VOD * CH 22 - IDLE TIE VOD *
CH 23 - IDLE TIE VOD * CH 24 - DCH 10
.


The red alarm seems to be in the physical layer.

I will remake the T1 crossover.


I ´ll let U know

 

[canopus]

Good shot!

I rebuilded the crossover and PUM!

The TMDI Card went green....

Now I have YELLOW alarm in the asterisk side....


Maybe clocking issues?

 

[canopus]

SPAN 1 IN ALARM (YELLOW)
pri show span 1
Primary D-channel: 24
Status: In Alarm, Up, Active
Switchtype: Lucent 5E
Type: Network
Remote type: Unknown node type
Overlap Dial: 0
Logical Channel Mapping: 0
Timer and counter settings:
N200: 3
N202: 3
K: 7
T200: 1000
T201: 1000
T202: 10000
T203: 10000
T303: 4000
T305: 30000
T308: 4000
T309: 6000
T312: 6000
T313: 4000
T-HOLD: 4000
T-RETRIEVE: 4000
T-RESPONSE: 4000
Q931 RX: 0
Q931 TX: 0
Q921 RX: 20
Q921 TX: 21
Q921 Outstanding: 0 (TEI=0)
Total active-calls:0 global:0
CC records:
Overlap Recv: No

 

[canopus]

Everything is working good!

Thanks for your help!

 

[canopus]

HUMMMMMM, something weird....

My another DLOP went DSBL.

>ld 60
DTI000
.stat

DTI TRK LOOP 100 - ENBL
FFMT/LCMT/YALMT: D4/ AMI/DG2
TRACKING
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : RED
CH 01 - IDLE DID VCE CH 02 - DSBL DID VCE
CH 03 - DSBL DID VCE CH 04 - DSBL DID VCE
CH 05 - DSBL DID VCE CH 06 - DSBL DID VCE
CH 07 - DSBL DID VCE CH 08 - DSBL DID VCE
CH 09 - DSBL DID VCE CH 10 - DSBL DID VCE
CH 11 - DSBL DID VCE CH 12 - DSBL DID VCE
CH 13 - DSBL DID VCE CH 14 - DSBL DID VCE
CH 15 - DSBL DID VCE CH 16 - DSBL DID VCE
CH 17 - DSBL DID VCE CH 18 - DSBL DID VCE
CH 19 - DSBL DID VCE CH 20 - DSBL DID VCE
CH 21 - DSBL DID VCE CH 22 - DSBL DID VCE
CH 23 - DSBL DID VCE CH 24 - DSBL DID VCE

PRI* TRK LOOP 101 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE VOD *
CH 03 - IDLE TIE VOD * CH 04 - IDLE TIE VOD *
CH 05 - IDLE TIE VOD * CH 06 - IDLE TIE VOD *
CH 07 - IDLE TIE VOD * CH 08 - IDLE TIE VOD *
CH 09 - IDLE TIE VOD * CH 10 - IDLE TIE VOD *
CH 11 - IDLE TIE VOD * CH 12 - IDLE TIE VOD *
CH 13 - IDLE TIE VOD * CH 14 - IDLE TIE VOD *
CH 15 - IDLE TIE VOD * CH 16 - IDLE TIE VOD *
CH 17 - IDLE TIE VOD * CH 18 - IDLE TIE VOD *
CH 19 - IDLE TIE VOD * CH 20 - IDLE TIE VOD *
CH 21 - IDLE TIE VOD * CH 22 - IDLE TIE VOD *
CH 23 - IDLE TIE VOD * CH 24 - DCH 10

any idea?

 

[curtismo]

Red alarm. Check your cabling on loop 100.