turning on/off light to external phone 2

[tellyteck1]

Hi, I am having great problems trying to use a MM mailbox to light a Mitel phone light. The scenario is as follows:

1. a number is set up as a CDP which is routed to a pri route to the mitel, the mitel fwds if phone not answered to a MM box. This all works. The problem is how to signal to the mitel to turn on and off its lights. The mitel can be programmed for any number to signal turning on or off. Does anyone have any suggestions? thank you in advance.AJK

 

[dlesap]

When the MMail is sending a voice mail notification to a remote site, a DCH message "NMS" is sent.
Do you see it going out your link? (LD 96 ENL MSGO XX)
Do you see it going in at remote site?

 

[RS528]

If it is a QSIG link between the Meridian and the Mitel you must also configure RCAP QMWO on your D-Channel.

 

[tellyteck1]

Hi, no I dont see NMS. Is it possible to modify the pri or do I have to rebuild it? Thank you for your help.AJK

 

[johnpoole]

those parms (rcap) can be modified, the msdl card must be enl msdl x fdl, for the changes to happen

john poole
bellsouth business
columbia,sc

 

[tellyteck1]

Hi John, thanks for the tip. I will try that in the morning. AJK

 

[tellyteck1]

Hi, what ld to I modify the RCAP in? I am hoping I can just modify the pri rather than taking it down. Do I need to associate the NMS to a number (to trigger pre-programmed remote to turn on light) somehow? For example the remote programs in 12 and 13 to represent the light coming on and off. The numbers need to come from the meridian. Any help is appreciated and thank you. AJK

 

[johnpoole]

that is
load 17
chg
adan chg dch x

a little different command then most changes, you have to do a ld 96 dis dch x auto, before any change, that does not interupt calls in progress, but stops any new calls, unless you have a backup. you alos have to dis the card the msdl is on in 96, after the change, then enl msdl x fdl, that download in needed for the changes to take place

john poole
bellsouth business
columbia,sc

 

[tellyteck1]

Thanks so much John, I will give it a go! Hopefully I get the lights working right on the mitel off the opt 11 and caller id to go through. Thank you, as always for your help. AJK

 

[tellyteck1]

Hi, I have tried all of the above. When I tried to put the following in RCAP all went in well but the members would not come out of the MBSY state. Also, when it came to trying to add QMWO and QMWI they would not go in. Bell tried to help but they finally took out all of the RCAP except COLP. They didnt know what to do wrt caller id being sent and the lights turning on and off. All is back up now but still the lights on the remote end dont turn on and off and the callers info is not sent to the far end.

COLP NDI CCBI CCNI PRI DV3I CTI QMWI

I managed to get around turning the light on by having a CDP for a DID number route to the mitel then have the mitel forward to a mailbox on the option 11. I then under the light indication field on the MM, inserted 55then the original DID. I mapped the 55 to the route to go to the Mitel. The mitel configured 55 to enable the light on the phone. I cannot however do the same adhoc solution to turn the light off from the mitel when the mail messages have been answered. Any help is greatly appreciated. Thank you AJK

 

[johnpoole]

if you use qsig, it will work. 1st time every time
Route:

REQ: prt
TYPE: rdb
CUST 0
ROUT 100

CODE
TYPE RDB
CUST 00
ROUT 100
DES  CISCO LOCAL
TKTP TIE
NPID_TBL_NUM   0
ESN  NO
CNVT NO
SAT  NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
    MODE PRA
    IFC  ISGF
    SBN  NO
    PNI  00000
    NCNA NO
    NCRD NO
    CHTY BCH
    CTYP UKWN
    INAC NO
    ISAR NO
    CPFXS YES
    DAPC NO
    INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 8760
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC  NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF  512
     OGF  512
     EOD  13952
     NRD  10112
     DDL  70
     ODT  4096
     RGV  640
     GRD  896
     SFB  3
     NBS  2048
     NBL  4096
     IENB  5
     TFD  0
     VSS  0
     VGD  6
DRNG NO
CDR  NO
VRAT NO
MUS  YES
MRT  10
RACD NO
FRL  0 0
FRL  1 0
FRL  2 0
FRL  3 0
FRL  4 0
FRL  5 0
FRL  6 0
FRL  7 0
OHQ  NO
OHQT 00
CBQ  NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART  0
SGRP 0
AACR NO

Trunk:

DES  CISCO LOCAL
TN   100 01
TYPE TIE
CDEN SD
CUST 0
TRK  PRI
PDCA 1
PCML MU
NCOS 1
RTMB 100 1
B-CHANNEL SIGNALING
TGAR 1
AST  NO
IAPG 0
CLS  CTD DTN WTA LPR APN THFD HKD
     P10 VNL
TKID
FCAR NO
DATE 24 FEB 2005

Dch:

ADAN     DCH 100
  CTYP MSDL
  GRP  0
  DNUM 13
  PORT 0
  DES  Cisco
  USR  PRI
  DCHL 0
  OTBF 32
  PARM RS422  DTE
  DRAT 64KC
  CLOK EXT
  IFC  ISGF
    PINX_CUST 0
    ISDN_MCNT 300
  CLID OPT0
  CO_TYPE  STD
  SIDE USR
  CNEG 1
  RLS  ID  **
  [b][COLOR=blue]RCAP COLP NDI CCBI CCNI PRI DV3I CTI  QMWI [/color][/b]
  PR_TRIGS DIV 2 3
           CNG 2 3
  PR_RTN NO
  MBGA NO
  OVLR YES
  DIDD 0
  OVLS NO
  T310 120
  T200 3
  T203 10
  N200 3
  N201 260
  K    7

john poole
bellsouth business
columbia,sc

 

[johnpoole]

and that was more work (copy and paste) then i usually do on a friday, but you did star me..thanks

john poole
bellsouth business
columbia,sc

 

[tellyteck1]

Aw shucks, I'll always give you a star - Promise!! I dont see alot of difference to yours except for the cos. Maybe the Mitel isnt set up right. I have no idea at this point!

I took a print out of the config.

TYPE: rdb

CUST 0

ROUT 25


TYPE RDB
CUST 00
DMOD
ROUT 25
DES TIE TO MITEL
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS INT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ISGF
SBN NO
PNI 00000
NCNA NO
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 3925
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096
IENB 5


PAGE 002

TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

TN 5 1

DATE

PAGE

DES


TN 005 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 3
RTMB 25 1
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS CTD DTN CND WTA LPR APN THFD HKD
P10 VNL
TKID
DATE 13 JUL 2005

 

[tellyteck1]

Hi John, apparently the reason the changes wont take is we have to upgrade 25.3 to 25.40b at the minimum. I am just writing this so there is some documentation. I was able to forcibly get some of the RCAPS in there but not all of them. Apparently the QSIG on release 25.3 is flaky. Have a good one.

 

[tellyteck1]

hi, one more thing after upgrade to 25.40b patch 17158 is required