skype to definity

[Phoneofalmere]

Hi everyone,

If got a request from my manager’s if it is possible to connect Spype to the pabx(s7800).They want to use it only fore incoming calls and not fore outgoing calls.
I already looked on the internet and the only thing I found was a 4 port getaway that connect thru analog lines to the definity but it is to small for the application that they want to use is fore .My Avaya provider has no solution for this question. Do’s any one know if there is some more software or a better gateway or has some one has it already got it working. If there is noting I got to built something or use multiple units of the gateway.

Thanks in advance for any reply

Bart

 

[Phoneofalmere]

well we bough a tiptel cyberbox 250 .
It’s only one analog line but fore the test it must do.

The only one problem the analog trunk card TN2147C

I Try to make it so that I don’t use the line output on the tiptel but the phone output .
But the card don’t recognise the signalling from the tiptel.

The trunk looks like this.

Voice System name: xxxxxxx - TRUNK GROUP

Group Number: 7 Group Type: co CDR Reports: y
Group Name: Internet lijn COR: 1 TN: 1 TAC: 389
Direction: incoming Outgoing Display? n
Dial Access? n Busy Threshold: 99 Night Service:
Country: 5 Version: a Incoming Destination: 19950
Comm Type: voice Auth Code? n Digit Absorption List:
Prefix-1? n Trunk Flash? n Toll Restricted? y

TRUNK PARAMETERS
Trunk Type: ground-start
Outgoing Dial Type: tone Cut-Through? n
Trunk Termination: rc Disconnect Timing(msec): 500

Auto Guard? n Call Still Held? n Sig Bit Inversion: none
Analog Loss Group: 6 Digital Loss Group: 11
Trunk Gain: high

Disconnect Supervision - In? y
Answer Supervision Timeout: 10 Receive Answer Supervision? n

TRUNK FEATURES
ACA Assignment? n Measured: internal
Maintenance Tests? y
Data Restriction? y

Abandoned Call Search? n
Suppress # Outpulsing? n




Receive Analog Incoming Call ID: disabled



Outgoing ANI: Ds1 Echo Cancellation? n






ADMINISTRABLE TIMERS
Send Incoming/Outgoing Disconnect Timers to TN465 Ports? n
Incoming Disconnect(msec): 500
Outgoing Dial Guard(msec): 1600



Ringing Monitor(msec): 5200 Incoming Seizure(msec): 100
Outgoing Seizure Response(sec): 5
Disconnect Signal Error(sec): 240
Flash Length(msec): 100





END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150

OUTPULSING INFORMATION
PPS: 10 Make(msec): 40 Break(msec): 60

TRUNK GROUP
Administered Members (min/max): 1/8
GROUP MEMBER ASSIGNMENTS Total Administered Members: 8

Port Code Sfx Name Night Mode Type Ans Delay
1: 01B1101 TN2147 C internet
2: 01B1102 TN2147 C internet
3: 01B1103 TN2147 C internet
4: 01B1104 TN2147 C internet
5: 01B1105 TN2147 C internet
6: 01B1106 TN2147 C internet
7: 01B1107 TN2147 C internet
8: 01B1108 TN2147 C internet


Has any one an idée how to make it so that the tiptel box can connect to the system.

Thanks in advance for any reply

Bart

 

[phoneguy55]

The trunk group is configured for ground start??? Maybe try loop-start

 

[Phoneofalmere]

Thx fore the post

I have made the chance tested it and it didn’t work.

I rely don’t get it why it won’t work

 

[TechJimF]

You stated you only have one trunk, I'm assuming that means one trunk port. You have 8 members in the trunk group. Try only having the one port that has dial tone as a member, remove the other 7.

Jim

 

[phonegoober]

you might want to try to set the TG as WATS and loop/start.

 

[Phoneofalmere]

Tanks fore all the posts .

I triad them all but the didn’t work.(and I am afraid it not going to work)

But I abandon the wish to do it whit a trunk and I now use normal analog lines .
The analog lines have a hot dial destinations to a vdn so there is no way to go any ware else than the destination vdn .

I program skype the following way.

I made 1 main skype account that transfers the calls to two divert secondary skype accounts
On two pc’s where the secondary skype accounts are running there are the tiptel boxes that connect to the pabx.

I note that this is not a solution fore large portions of calls.

So my quest go’s on fore a better skype gate way.

Again many thanks fore all the posts

bart