Programing a T1

[FireFighter78]

Hi Guys,

I am building an Option 11 release 21.35 (to replace an Option 21 that is dying of a slow and painful death) I guess I should say that I am remodeling an Option 11 seeing that it is used.

So they had it setup with some multi site setup, ACD stuff, etc. The trunk stuff is kicking my butt big time. They were using NARS/BARS and other stuff that I understand conceptually. I really need some help finding the stuff I need to OUT and then putting it back in for our fairly simple T1-PRI (one location, everything in and out the same telco T1).

My level of understanding is medium, I think???? I don’t really need some one to do it for me (although that would be nice) but I could use a hand to hold onto when the road gets rough (the outbound path is quite rutty).

Thanks!!!!

 

[phonz1]

can you post the T-1 config, the RDB, the DCH etc, from the 11 and if you can, the 21?

 

[FireFighter78]

This configuration is what I will trying at the end of business today. There is no D channel. And I cannot get information off of the 21. I will be able to bounce the T-1 when I try it on the 11.

TYPE RDB
CUST 00
DMOD
ROUT 0
TKTP DID
SAT NO
RCLS EXT
DTRK YES
DGTP DTI
ISDN NO
PTYP DCO
AUTO NO
DNIS NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 9
CPP NO
TARG
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
TFD 0
SST 5 0
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR YES
INC YES
LAST NO
TTA NO
QREC NO
OAL NO
OTL YES
AIA YES
OAN YES
OPD NO
NATL YES
MUS NO
MR NO


PAGE 002

RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TTBL 0
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0



TN 004 01
TYPE DID
CDEN SD
CUST 0
NCOS 0
RTMB 0 1
A/B BIT SIGNALING
NITE 8199
SIGL EAM
STRI/STRO WNK WNK
SUPN YES
CLS UNR DTN WTA LPR APN THFD HKD
P10 NTC
TKID
DATE 28 APR 2009

TN 004 24
TYPE DID
CDEN SD
CUST 0
NCOS 0
RTMB 0 24
A/B BIT SIGNALING
NITE 8199
SIGL EAM
STRI/STRO WNK WNK
SUPN YES
CLS UNR DTN WTA LPR APN THFD HKD
P10 NTC
TKID
DATE 28 APR 2009

 

[phonz1]

I see your acod is 9, and that may conflict with your bars... Change the acod to an unused 4 digit number.... otherwise I don't see why this shouldn't work

 

[RKDavis]

I noticed that you have not set the primary reference for the clock controller on the dti card. Go to ld 73,DDB and set pref to the loop number of the dti card. That is why the dial tone sounded like it was distorted. Also reset your counter in ld 60 . rcnt. then list your counters to make sure there are no slips.

 

[FireFighter78]

Hey guess what - teleco gave me the wrong information. After talking to a couple techs we found out that we were not using ESF but SF (D3).

Thanks guys for all your help we are now all set to make the switch switch Saturday.

Anyone want to purchase a slightly used Option 21? I want to use it for target practice myself.

 

[phonz1]

good luck