PRI config help

[SMMC]

Trying to build a PRI to go into a Digium TE122P. All the vendor can tell me is it's built as a PRI B8Zs ESSF. I can't figure out how to build the trunks to get calls across. I can get it green, trunks idle all day and d-channel established but all I get in return is a reorder? Anyone using this type of card please help. Thanks

 

[phonz1]

you'll need to post some config info for like, the dch, the route, a trunk on the span etc....

 

[EddieDuece]

Build new trunks in LD 14. At the request prompt type;
REQ new 24

This way you can build out all 24 channels at once.

 

[SMMC]

Here is what I have built currently. I have tried other signaling on the trunks like E&M with no luck.
Trunks:
TN 066 01
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 66 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DIP CND WTA LPR APN THFD HKD
P10 VNL
TKID

Route:
TYPE RDB
CUST 00
ROUT 66
DES EMACS
TKTP DID
NPID_TBL_NUM 0
SAT NO
RCLS EXT
DTRK YES
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 5966
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
TFD 0
DRNG NO
CDR NO


PAGE 002

MUS NO
MR NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

D-Channel:
ADAN DCH 4
CTYP MSDL
GRP 0
DNUM 15
PORT 1
DES emacs
USR PRI
DCHL 66
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
RCAP COLP
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
DSC:
DSC 2495
FLEN 0
DSP LSC
RLI 22
NPA
NXX
RLI:
RLI 22
ENTR 0
LTER NO
ROUT 66
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
CNV NO
EXP NO
FRL 0
DMI 0
FCI 0
FSNI 0
SBOC NRR
OHQ NO
CBQ NO

ISET 0
NALT 5
MFRL 0

 

[EddieDuece]

Here is one of mine. Change your trunk type to TIE.

TN 050 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 2
RTMB 10 1
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS CTD DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID 1
AACR NO

 

[EddieDuece]

Also, make sure the TGAR on the phone you are testing from is NOT set to 01. Cannot match the TARG of the route.

 

[RKDavis]

You can turn on D channel messaging. In ld 96 enl msgo and msgi for the dch number. This will help in finding the problem.

 

[GHTROUT]

Notice the CLS:

[tt]CLS UNR [red]DIP[/red] CND WTA LPR APN THFD HKD
P10 VNL[/tt]

I think you want [red]DTN[/red] (DTMF, rather than pulse)

Might be the issue, but either way it should be DTN

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators