Line Side Connection to Cisco CCM from Nortel 2

[Stagemusic]

Help is needed folks. I am tying a Cisco CCM and our Nortel 1000m together. The Cisco server is sitting in the same room as the Nortel and we are using a Line Side T-1 card for a connection. I had no trouble building the DCH, and RDB. However, when I go to add members to the PRI route, this is the command it asks for. I was expecting to see TRK (in which case the response is PRI). What am I doing wrong, or what is the correct response here?

EQ new 23
TYPE tie
TN 20 0 11 0
DES Cisco
XTRK

 

[Stagemusic]

EDIT:::

Help is needed folks. I am tying a Cisco CCM and our Nortel 1000m together. The Cisco server is sitting in the same room as the Nortel and we are using a Line Side T-1 card for a connection. I had no trouble building the DCH, and RDB. However, when I go to add members to the PRI route, this is the command it asks for. I was expecting to see TRK (in which case the response is PRI). What am I doing wrong, or what is the correct response here?

EQ new 23
TYPE tie
TN 20 0 11 0
DES Cisco
XTRK

The only proper responses that I can find to the command are: EXUT
ITG1
ITG2
XCOT
XDID
XEM
XFEM
XUT

Note: None of these allow me to add members to my PRI Route.

HELP!!!

 

[janeenaj]

maybe its becuase you're using a line side t1 card instead of a pri card such as a ntrb21 tmdi card or a ntak09 dti/pri card

 

[Stagemusic]

Thank you for your kind response. Now could you please explain a little more in depth? The type would still be TIE and the XTRK command would still apply.

 

[johnpoole]

neither one, a line side t1 is a station card.. no dch, no route.. build port 0 (yes zero, not 1 like a trunk card) as new 500.. you don't need a line side t1 card.. that works great between a keysystem and a pbx.. between your pbx and the ccm you need the same type of card your using between your switch and the pstn.. i use dual pri's, smaller switches use the tmdi.. the only type that a line side will accept is 500 and of course you will not get ask for route and member..

john poole
bellsouth business
columbia,sc

 

[Stagemusic]

Thanks for the explanation John. That helped alot. I do have a Dual PRI card that I can use and have connected it However, when I try to build the route it gives me this error.

RTMB 5
SCH0220
RTMB
SCH0220
RTMB

Sch220 says: SCH0220
Wrong number of input fields for prompt RTMB.

Severity: Info

the swch code appears after I enter the Route and then space bar before the member.

 

[Johnthephoneguy]

Do you already have the route 5 built?

 

[TAnselm]

First you have to build the route in 16

Then you when it asks for RTMB
you have to add the Route & the Member

i.e. 5 1

 

[Stagemusic]

OK...got that corrected. It was built but was not in correct form. Now here is my new issue.

TYPE tie
TN 3 1
DES Cisco
PDCA 1
PCML mu
CUST 0
NCOS 4
RTMB 5 1

SCH3959
RTMB !
>err sch3959
>

SCH3959
A non-PRI loop number was specified in the TN, but the route member is
PRA mode.

 

[Johnthephoneguy]

Post your RDB for route 5

 

[Stagemusic]

Here you go...thanks for looking at it.

REQ: prt
TYPE: rdb
CUST 0
ROUT 5

TYPE RDB
CUST 00
ROUT 5
DES CISCO
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ISGF
SBN NO
PNI 00000
NCNA NO
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 5905
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096


PAGE 002


IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

REQ:

 

[johnpoole]

TN 3 1
the code is saying that loop 3 is not a pri card.. if it's still the line side t1 then it's not going to work.. the route is pri, the card is t1.. a tmdi card can have a d, a line side can not

john poole
bellsouth business
columbia,sc

 

[Stagemusic]

Loop 3 is a dual PRI card. Line Side is gone.

 

[yyrkroon]

post your cequ

 

[Stagemusic]

I see it in there.

REQ prt
TYPE cequ

CEQU
MPED 8D
TERM
REMO
TERD
REMD
TERQ
REMQ
SUPL 004 008 020 V080
V084 N096 N100 N140
V152 V156
SUPC
SUPF
XCT 000 016
TDS * 000 * 016
CONF * 001 * 017
MFSD * 000 * 016

DLOP NUM DCH FRM TMDI LCMT YALM TRSH
TRK 002 24 ESF NO B8S FDL 00
003 24 ESF NO B8S FDL 00
019 24 ESF NO B8S FDL 00
PRI 018 23 ESF NO B8S FDL 00
MISP
EXT0 3PE
CNI 009 000 000
EXT1 3PE
CNI 009 000 000
MCFN 509 MB

 

[yyrkroon]

you built loop 3 as a DTI loop and not PRI

 

[johnpoole]

PRI 018 23 ESF NO B8S FDL 00

you need to add a line for the new dual to match this one.. loop 18 is the only pri in the switch.. and it needs to read pri 18 24 esf.. the 23 was a type-o

john poole
bellsouth business
columbia,sc

 

[yyrkroon]

delete loop 3 and rebuild it as a PRI. At the MODE prompt type PRI and not TRK

 

[johnpoole]

and you can't use 5.. you can use 2 and 3.. slot 0 and 1 are conf/tds.. 2 and 3 are blank 4 in a controller, and it takes speech paths 3,4,5,6 so the slot to the right of that controller can't be used for a dual

john poole
bellsouth business
columbia,sc

 

[Stagemusic]

and you can't use 5.. you can use 2 and 3.. slot 0 and 1 are conf/tds.. 2 and 3 are blank 4 in a controller, and it takes speech paths 3,4,5,6 so the slot to the right of that controller can't be used for a dual

Yup, figured that one out too. I am going to move the DTI on 19 to 3 and use 19 as my PRI. Have to because of the MSDL cable. I think you guys got me on the right track.

Thank you and have a star.

CWY.