Is there a way to change the IP address on a call pilot 100 Through a phone using admin codes? (Feature 983)
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Shaun E on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
IP Address for Call Pilot
- Thread starter silver987
- Start date
NorstarOption
Technical User
No you have to use Voicemail Manager to change the ip
phoneguy427
Technical User
There is no vmail manager for call pilot, set your pc to 192.168.110.11 or any other .xxx. Browse to 192.168.110.10 and log into call pilot, then you can go to settings and change the ip.
- Thread starter
- #4
Thats the problem I changed the IP to what the network person gave me as a usable IP for there network and I think they gave me a bogus IP. The network won't see it and I can't get in with my laptop anymore. They gave me an IP of 69.88.118.146 That just dosen't sound like a lagit IP to me but then I'm not a computer guy....
Any ideas would be apreciated, I tried hooking my laptop to it using the new IP and nothing...I tried with a regular cat-5e and a crossover cable with no results.
Any ideas would be apreciated, I tried hooking my laptop to it using the new IP and nothing...I tried with a regular cat-5e and a crossover cable with no results.
phoneguy427
Technical User
I hope thyis helps.
32 Chapter 5 Initializing the CallPilot 100/150
N0012710 02
Configuring the terminal
The terminal or terminal emulation program you use must be VT100 compatible and must support
the ASCII Character set. If the terminal does not support the ASCII Character set, the text displays
incorrectly.
You must configure your terminal to the following communications parameters:
• 9600 bits per second
• 8 data bits
• no parity
• 1 stop bit
• no flow control
For information about how to set these parameters, refer to the documentation for your terminal or
terminal emulation program.
Changing the IP address using the terminal
To change the IP address:
1 Attach the serial cable to the serial port on the CallPilot 100/150. For information about the
location of the serial port, refer to Figure 3 on page 25.
2 Attach the other end of the cable to the serial port on the terminal or computer.
3 Ensure that your terminal or computer is powered up.
4 If you are using a computer, start your terminal emulation program.
5 Remove power from the CallPilot 100/150.
6 Reconnect power to the CallPilot 100/150.
The prompt To change any of this, press any key within 2 seconds appears.
Note: The location of the transmit (TX) and receive (RX) pins on your terminal can vary.
Refer to your terminal or computer documentation to confirm pin locations.
Note: Steps 5 and 6 are used to force the CallPilot 100/150 to reboot. You can change
the IP address only while the CallPilot 100/150 is booting up.
Note: It takes approximately one minute for this prompt to appear.
Chapter 5 Initializing the CallPilot 100/150 33
CallPilot 100/150 Installation and Maintenance Guide
7 Press the Enter key.
The prompt (M)odify any of this or (C)ontinue? appears.
8 Press the M key and press the Enter key.
The prompt Do you want a LAN interface? appears.
9 Press the Y key and press the Enter key.
The prompt This board’s LAN IP Address (0.0.0.0 = RARP) appears.
10 Type the IP address for the CallPilot 100/150 in a valid dotted format and press the Enter key.
The prompt Subnet mask for LAN (0 for none) appears.
11 Type the Subnet Mask for the CallPilot 100/150 in a valid dotted format and press the Enter
key.
The prompt Should there be a default gateway for packet routing? appears.
12 If the CallPilot 100/150 needs a next hop router, press the Y key and press the Enter key.
If the CallPilot 100/150 does not need a next hop router, press the N key, press the Enter key
and go to step 15.
The prompt IP address of default gateway? appears.
13 Type the IP address of the next hop router in a valid dotted format and press the Enter key.
14 Press the Enter key until the following prompt appears.
(M)odify any of this or (C)ontinue?
15 Press the C key and press the Enter key.
16 Connect the LAN cable to the Ethernet port on the CallPilot 100/150.
You can now initialize the CallPilot parameters. For information about how to initialize the
CallPilot, refer to “Running the Quick Install Wizard” on page 35.
Note: If you do not press a key within 2 seconds of this prompt appearing, repeat
steps 5 and 6.
32 Chapter 5 Initializing the CallPilot 100/150
N0012710 02
Configuring the terminal
The terminal or terminal emulation program you use must be VT100 compatible and must support
the ASCII Character set. If the terminal does not support the ASCII Character set, the text displays
incorrectly.
You must configure your terminal to the following communications parameters:
• 9600 bits per second
• 8 data bits
• no parity
• 1 stop bit
• no flow control
For information about how to set these parameters, refer to the documentation for your terminal or
terminal emulation program.
Changing the IP address using the terminal
To change the IP address:
1 Attach the serial cable to the serial port on the CallPilot 100/150. For information about the
location of the serial port, refer to Figure 3 on page 25.
2 Attach the other end of the cable to the serial port on the terminal or computer.
3 Ensure that your terminal or computer is powered up.
4 If you are using a computer, start your terminal emulation program.
5 Remove power from the CallPilot 100/150.
6 Reconnect power to the CallPilot 100/150.
The prompt To change any of this, press any key within 2 seconds appears.
Note: The location of the transmit (TX) and receive (RX) pins on your terminal can vary.
Refer to your terminal or computer documentation to confirm pin locations.
Note: Steps 5 and 6 are used to force the CallPilot 100/150 to reboot. You can change
the IP address only while the CallPilot 100/150 is booting up.
Note: It takes approximately one minute for this prompt to appear.
Chapter 5 Initializing the CallPilot 100/150 33
CallPilot 100/150 Installation and Maintenance Guide
7 Press the Enter key.
The prompt (M)odify any of this or (C)ontinue? appears.
8 Press the M key and press the Enter key.
The prompt Do you want a LAN interface? appears.
9 Press the Y key and press the Enter key.
The prompt This board’s LAN IP Address (0.0.0.0 = RARP) appears.
10 Type the IP address for the CallPilot 100/150 in a valid dotted format and press the Enter key.
The prompt Subnet mask for LAN (0 for none) appears.
11 Type the Subnet Mask for the CallPilot 100/150 in a valid dotted format and press the Enter
key.
The prompt Should there be a default gateway for packet routing? appears.
12 If the CallPilot 100/150 needs a next hop router, press the Y key and press the Enter key.
If the CallPilot 100/150 does not need a next hop router, press the N key, press the Enter key
and go to step 15.
The prompt IP address of default gateway? appears.
13 Type the IP address of the next hop router in a valid dotted format and press the Enter key.
14 Press the Enter key until the following prompt appears.
(M)odify any of this or (C)ontinue?
15 Press the C key and press the Enter key.
16 Connect the LAN cable to the Ethernet port on the CallPilot 100/150.
You can now initialize the CallPilot parameters. For information about how to initialize the
CallPilot, refer to “Running the Quick Install Wizard” on page 35.
Note: If you do not press a key within 2 seconds of this prompt appearing, repeat
steps 5 and 6.
phoneguy427
Technical User
Or if you did change the address to 69.88.118.146 set your laptop to 69.88.118.anything and use your crossover cable to talk to call pilot with explorer using .146.
- Thread starter
- #7
Your right, of course... I totaly forgot the laptop needs to be in that range. Thanks for the input.
- Status
Similar threads
- Locked
- Question
