E1 issue !!!

[rsadf2006]

Hi all

In posted conf. u 'll find the configuration which I implemented in both side using E1 channel( One Side CS1000M and Other is CS1000E)

When i tried to test the call between two site I could not, once i dail 81 i got a tone but when i dail any extention in the remote site nothing there!!!

If there is any mistake plz inform me...

To understand what I need is that when I dial ACOD "81" from (Site1) i can access to (site 2) and dial any extention in their system and vice versa.


Thank you

first Site

ld 22

REQ prt
TYPE adan
ADAN DCH 133
CTYP MSDL
MG_CARD 012 1 01
PORT 1
DES HQ
USR PRI
DCHL 133
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
NASA NO
IFC SL1
SIDE USR
CNEG 1
RLS ID 5
RCAP ND2
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7

>ld 21

REQ: prt
TYPE: rdb
CUST 0
ROUT 133
TYPE RDB
CUST 00
ROUT 133
DES HQ
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
IDEF NET
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC SL1
PNI 000001
NCNA YES
NCRD NO
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 133
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
SIGO STD
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
NBS 2048
NBL 4096

PAGE 002
IENB 5
TFD 0
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DRNG NO
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 133 133
SGRP 0
ARDN NO
AACR NO

>ld 20
PT0000
REQ: prt
TYPE: tie
TN 133 1
DATE
PAGE
DES HQ
TN 133 01 VIRTUAL
TYPE TIE
CDEN SD
CUST 0
TRK PRI2
PDCA 1
PCML A
NCOS 7
RTMB 133 1
B-CHANNEL SIGNALING
TGAR 20
AST NO
IAPG 0
CLS TLD DTN CND ECD WTA LPR APN THFD XREP BARD SPCD
P10 VNL
TKID
AACR NO
DAT 8 DEC 2009



Second Site

>LD 22

REQ PRT
TYPE ADAN DCH 35
ADAN DCH 35
CTYP MSDL
GRP 2
DNUM 7
PORT 1
DES SMF_L39_A81
USR PRI
DCHL 67
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
NASA NO
IFC SL1
SIDE NET
SEMT 1
CNEG 1
RLS ID 5
RCAP ND2
MBGA NO
OVLR YES
DIDD 0
OVLS YES
OVLT 0
T200 3
T203 10
N200 3
N201 260
K 7



LD 21
REQ: PRT
TYPE: RDB
CUST 0
ROUT 39
TYPE RDB
CUST 00
ROUT 39
DES SMF
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
IDEF NET
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO NO
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 81
TCPP NO
TARG 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
29 30 31
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 1 *
NDNO 1
DEXT YES
DNAM YES
SIGO STD
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
NBS 2048
NBL 4096
TFD 0
DTD NO
SCDT NO
2 DT NO
DRNG NO
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
MUS NO
PANS YES
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
AUTH NO
TTBL 0
ATAN NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 10081 39
SGRP 0
AACR NO


>LD 20
REQ: PRT
TYPE: TNB
TN 67 1
DATE
PAGE
DES
DES SMF
TN 067 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI2
PDCA 1
PCML A
NCOS 7
RTMB 39 1
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS CTD DTN WTA LPR APN THFD XREP BARD
P10 VNL
TKID 810000
AACR NO
DATE 14 APR 2010

 

[PERRYPJ]

Turn on DCH Messaging for the Route and see what you are sending, if your sending correctly then turn on the DCH Messaging for the far end and see what you getting

OLD ROLMEN WORKING ON NORTELS AND AVAYA

 

[MikeRizz]

Try dialing 81 ( acod ) then 9, plus your 4 digit DN. The 9 gives you access to far ends Nars/Bars. If this works you will need to insert a 9 in the RLI.

 

[bignose21]

You also have one end set for overlap signalling and the other on block on the DCH. Should make a decision which to use and match them up. Also you would be better using CDP DSC instead of ACOD to access across the TIE.