Configuring E1 lineside in Opt11

[stemanc]

Does anyone have the instructions for configuring a E1 lineside dip switches and the configuration of the card, it's going to connect to a MPS500

 

[pronei]

Goto

http://support.nortel.com

and create an account. You'll find all the tech guides for everything nortel makes.

 

[sietecinco]

You Need the next configuration:

LEI::>d c
LEI S/N NT5D34AC 02 NNTM840090Z3 Software Version 3.06 2/26/00 12:25
Alarms Enabled: YES Self Clearing Enabled: YES

Alarm Level 1 Threshold Value E-6 Threshold Duration (in seconds) 10
Alarm Level 2 Threshold Value E-4 Threshold Duration (in seconds) 10
Frame Slips Alarm Level Threshold 100 Threshold Duration (in minutes) 2

Current Dip Switch S1 Settings (S1..S8)
Switch 1 OFF - MMI Port 2400 Baud
Switch 2,8 OFF, OFF - E1 Signaling Loop Start
Switch 3-6 Shelf Address 0x07
Switch 7 OFF
Current Dip Switch S2 Settings (S1..S8)
Switch 1 ON - CRC-4 Disabled
Switch 2 OFF - E1 Coding HDB3
Switch 3-5 Not Used
Switch 6 ON - Line Processing on link failure is On-Hook
Switch 7 OFF - No Daisy Chaining to MMI
Switch 8 ON - MMI Master
LEI::>
---------
LEI::>d m
Dip Switches set to Loop Start Signaling
Incoming and outgoing calls are in reference to the CPE.
All ABCD bits are with respect to SENDing from LEI/M1 to CPE or
RECEIVing from CPE to LEI/M1.

IDLE SEND: 0101
IDLE RECEIVE: 0101
BLOCKING RECEIVE is disabled.
Incoming call RINGER-ON SEND: 0000
Incoming call RINGER-OFF SEND: 0101
Incoming call OFFHOOK RECEIVE: 1111
Incoming call CONNECTED SEND: 0101
Incoming call (Far End) DISCONNECT SEND: 1111
Incoming call (CPE) DISCONNECT RECEIVE: 0101

Outgoing call SEIZE RECEIVE: 1111
Outgoing call SEIZE ACK SEND is disabled.
Outgoing call DIAL MAKE RECEIVE: 1111
Outgoing call DIAL BREAK RECEIVE: 0101
Outgoing call ANSWERED SEND: 0101
Outgoing call (CPE) DISCONNECT RECEIVE: 0101
Outgoing call (Far End) DISCONNECT SEND: 1111

Disconnect Time : 880 ms
Intercall Time : 0 ms
Only A and B bits are used on receive.

LEI::>
--------------
LEI::>d p
LEI E1 Interface Performance Log
2/26/00 12:26
Data for the past 26 Minutes
Errored Bursty Unavailable Loss Frame Frame Slip Error
Seconds Seconds Seconds Seconds Seconds Counter
1566 0 1566 1566 200 65535
LEI::>d s
LEI S/N NT5D34AC 02 NNTM840090Z3 Software Version 3.06 2/26/00 12:26


In Alarm State: YES

E1 Link at Alarm Level 2 Loss of Signal Error
Phone Status
Port 0 ON HOOK Port 1 ON HOOK Port 2 ON HOOK Port 3 ON HOOK
Port 4 ON HOOK Port 5 ON HOOK Port 6 ON HOOK Port 7 ON HOOK
Port 8 ON HOOK Port 9 ON HOOK Port 10 ON HOOK Port 11 ON HOOK
Port 12 ON HOOK Port 13 ON HOOK Port 14 ON HOOK Port 15 ON HOOK
Port 16 ON HOOK Port 17 ON HOOK Port 18 ON HOOK Port 19 ON HOOK
Port 20 ON HOOK Port 21 ON HOOK Port 22 ON HOOK Port 23 ON HOOK
Port 24 ON HOOK Port 25 ON HOOK Port 26 ON HOOK Port 27 ON HOOK
Port 28 ON HOOK Port 29 ON HOOK
LEI::>

 

[stemanc]

Thanks alot use the config details provided and it works just need some MPS config