Search results for query: *

I will be using eBGP rarther than iBGP. But an example of what I need but not real addressing is: router bgp 2 bgp log-neighbor-changes network 128.16.16.0 mask 255.255.255.0 network 130.130.0.0 neighbor 10.10.10.1 remote-as 1 neighbor 10.10.10.1 advertise-map ADVERTISE exist-map...

I wish to have a conditional advertisement for some of the networks statements to a BGP neighbour while some are always advertised, assuming the route for that network is in the routing table. This is advertising between a pair of AS on the same router. Which is a 7200 running a 12.4 code...

The only way to edit using the sequence number is on a Extended ACL so using a acl number over 101 or using a named ACL. Which I prefer.

I am looking for a app that will be able to collect all of the ip address it can see on the network with their mac entries as well. Currently I am using IPtools to do the ping sweep but it doesn’t list the macs as well. Thanks

I have to say that is what I thought and has worked previously, it is just this FW is not responing. thanks

I am running a K9 code on a 2821 rotuer and need to SSH to the firewall attached, which I can't access directly from the PC I am working on. What do i need to configure on the 2800 to act as the SSH source. Cheers

can you post a bit of a deubug standby or debug standby errors but I have never used timers that close together. Are you seeing any other errors on either of the two Fast etherents?

What MSFC do you have? The boot system command is missing from your config. Try typing boot<cr> this will look in the sup-bootflash & then any flash cards for a boot image to boot from. if there is no image on your sup-bootflash you will need to use an external card either pcmcia flash...

Manage the switch;) But go Layer 3 with the 6509's and run HSRP from the 6500 down to the access switch much quicker convergence than Spamming tree:D

I did put this in yr other thread but on just number of packets look at sh int after you have cleard the counters. This will let you know the raw number of packets. Otherwise download the Netflow engine from Cisco's web site which will log the output/input of the interfaces. You can get a...

I would say no. You have something wrong! I dont use 4500 only 6509 but I have never seen that on one of ours! When you say every port what blades do you have in the Cat?

I know I can't as behind to many FW's which don't allow tftp

if you were using enable secret comand you should have a 5 after if it was just an enable password it would have been a 7 which you can decode via getpass from Boson a 5 is a bit more dificult but it still should have been the correct password. What emulation software are you using...

But with port security it only shuts down the port in realtion to MAC addresses or you have a limit to them per port. And ACL is more powerful and if you are using a layer 3 switch the vlan interface is similar to a real fast ethernet on a router. There are other ways to log an acl. Debug...

post some config as I have never used the 500 switches. Is it a flat layer2 LAN between the 2 rooms? Or is there some routing going on?

so you are not able to pick up DHCP in room 1? if the answer is yes: What can you see if you statically assign a pc in room 1 and then try an ping your default gateway? then a server or a device on your network.

No best that they all have their own connection to the Gig Switches otherwise if you lost one in the diasy chain you would lose anything connected below them.

It looks like you are trying policy based routing. The natting is dependant on which interface you are have the inside & outside configured on, and any acl. i.e the inside will be the Ethernet of the 1841 Outside the Dialer interface So a packet going in the ethernet the routed to the other...

as you have vlan1 shut. Try adding some vlans to the trunk int g0/1 switchport trunk allowed vlan 101 you should then see the vlan come up. Also post a: sh span & sh int g0/1

are you running Hybrid or Native? Is the 6500 configured as a switch with the MSFC as a router or as a Layer 3 Switch. As you will either just be running one code and one config otherwise you may have two codes IOS & CATOS and two configs.