Search results for query: *

oh, and we haven't deployed i{rint yet, so i can't use iPrint printer pooling.

it's not the spooling from a queue that's a problem. having a queue is actually OK because the app i'm using (FaxPress) can only print to a traditional netware queue. the problem i'm actually trying to get around is that when multiple NDPS printers service a traditional queue, the load isn't...

i know with traditional netware queues, you could have multiple printers servicing a queue, thereby splitting the load across multiple printers. is there a way to do the same thing with NDPS without having to use traditional queues?

...can answer the incoming calls. the type is Group Ring and Auto Logout. i added all of the extensions as members and programmed login buttons using *44. this works, but i need to improve it. to that end i have three specific questions: 1) right now when you call it, it just rings until...

I have a mission-critical laserjet 8150 that occasionally goes off-line when it goes in to powersave mode. therefore, when it receives a job, the printer does not exit powersave and print. does anyone know what the cause of this may be? thanks! - Carl

I think the printer will automatically form feed if it doesn't receive any data for 90 seconds. What happens if you wait 90 seconds or more? - Carl

Try Bay Copy and Data in Tampa, FL. We use remanufactured cartridges from them all the time. They may not carry remans for a 3500, but it's worth a shot if you're really that desperate. - Carl

Oh, sorry. I misintrepreted what you were asking in your first question. Do you have the paper type (not size, type) set to ANY? Based on what I read in the manual, you need to specify the paper type.

can i upload a custom banner page to the jetdirect card?

Change tray 1 mode from casette to first. This will cause the printer to always from from tray 1 first if there is media loaded in it, regardless of the paper type specified on the printer or in the print job.

I have 2 network cards in a 5si. I want the plain-text print jobs sent to one network card to come out on the face-down tray and the print plain-text jobs sent to the other network card to out out on the face-up tray. The print jobs come from a mainframe application I have no control over, so I...

In your system try, right click the red N and pick Novell Client Properties. On the default capture tab, uncheck "Form Feed". Also, in the printer properties on the computer, there is also a "Form Feed" check mark on one of the tabs. I don't remember which one, and I don't have a printer...

I have three 8000's that jam only when feeding from tray 3. The page stops before it reaches the PS1 registration sensor below the toner cartridge. I have to open the right door to remove the page. After I clear the jam, sometimes it will print one page and jam on the second page, leaving the...

i think you want CBWFQ. that will allow you to set up an access-list to select the Citrix traffic and give it at least 64k. the rest of the traffic gets WFQ, as described above. see this page: http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fqos_c/fqcprt2/qcfwfq.htm#1041636

check out this page: http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fqos_c/fqcprt2/qcfconmg.htm

do you have any quality of service specified on your router? i don't have much experience with QoS, but one of the cisco books i have describes a few options. based on what i read, it seems weighted fair queuing may be good for you. the command is fair-queue this will configure a bunch of...

You will get ADMIN DOWN if the link signal on the Ethernet goes away, i.e. disconnected cable or power-cycling the modem, not PROTOCOL DOWN.

Let me clarify: The command doesn't give me an error. It just doesn't seem to do anything. When I do sh ip route it says "gateway of last resort is 0.0.0.0" instead of the address provided via DHCP. But now I'm thinking it's not necissarily a problem with the ip route command, but a problem...

my router doesn't have FastEthernet interfaces. the interface name is correct.

I am trying to use a 2514 as a broadband router. I have it almost working but... ...I currently have to add a static route and specify the next-hop on my ISP's netowrk at x.x.x.x: ip route 0.0.0.0 0.0.0.0 x.x.x.x Is it possible to have the router next-hop router automatically added? I looked...