Recent content by vistech1

Do you have the DEVELOPMENT SYSTEM installed? We found that we needed to have this installed to run make. We got a similar error without the DEV installed.

You might want to look at SCO TA# 107669 http://wdb1.sco.com/kb/showta?taid=107669&qid=1516724747&sid=1004548140&pgnum=1 I found it helpful on customer sites that did not use DNS.

I have a customer running 5.0.6 Each time they go into scoadmin and exit a dump file is created in: /usr/ccs/bin/elf/ back in February I conencted and found: # ls -l dump* lrwxrwxrwx 1 root sys 45 Feb 27 04:00 dump -> /opt/K/SCO/unixds/5.1.2A/usr/ccs/bin/elf/dump lrwxrwxrwx...

Customer called and was having "cron" problems again. found that the permissions on usr/sbin/cron was 777 and needed to be changed to 2550.

I discovered that the problem was with group ownership on the NPIPE file. I throughly checked and rechecked the man pages on cron (specifically paying attention to allow and deny) but did not see where the configuration on the customer server was different than was implied in the man page)...

I discovered that the problem was with permissions on the NPIPE file. I throughly checked and rechecked the man pages on cron (specifically paying attention to allow and deny) but did not see where the configuration on the customer server was different than was implied in the man page). The...

I should have mentioned that I read the man page on crontab prior to posting. This is what I had found. allow and deny files Users can use crontab if their names appear in the file /etc/cron.d/cron.allow. If that file does not exist, the file /etc/cron.d/cron.deny is checked to determine if...

A customer of mine is having problems submitting cron jobs as other users (root works fine). Unixware 7.1.3 They have a user "support" When support user submits its cron: in support's home diretory is a file called support.cron -rwxrwxrwx 1 support support 126 May 12 2004...

A customer of mine is having the same problems except this is on a Unixware v7.1.3 They have a user "support" When support user submits its cron: in support's home diretory is a file called support.cron -rwxrwxrwx 1 support support 126 May 12 2004 support.cron when I vi the...

I am trying to load Unixware 7.1.4 on a Dell 2650 Poweredge with a PercRaid 3DC controller. This controller card was purchased and used because there are known problems with the onboard controller and Unixware. SCO Tech Support had emailed me an HBA driver that they thought would work. It...

From SCO Technical Article 104588, please read it in it's entirety before implementing anything. Take the following steps (this MAY be done in multiuser mode): cd /etc/auth/system mv ttys /tmp/ttys.bad (if you just copy it, you need to manually...

Take a look here if your are talking about openserver. FAQ58-1366 It may help you.

On OpenServer 5.0.7 do a man on sysinfo the sysinfo ccommand may provide you with more infomration than you need. not sure if this is available on older versions.

This may help. I explaines that the NSTRPAGES parameter in the kernel may need to be set higher. http://stage.caldera.com/cgi-bin/ssl_reference?101596

the command I use to check processor spped is: hw -rcpu -v I have SCO openserver 5.0.5 running on a P166 PC. # uname -X System = SCO_SV Node = phonetec Release = 3.2v5.0.5 KernelID = 98/07/02 Machine = Pentium BusType = ISA Serial = 2GH072094 Users = 130-user OEM# = 0 Origin# = 1 NumCPU = 1...