Recent content by tech4ultimate

Common guys!!! amriddle01 and hairlessupportmonkey...respond, you started this. The certification guru backed up his talk with evidence and you guys go silent. I am rooting for you guys...hoping you come back.

Embedded Voice Mail is installed on IP500 (5.0.18). Voice mail was upgraded with R5 files. Should there be a system prompt when using the "transfer by name" action? I get silence after selecting programmed option for "transfer by name". There is dead air and name inputs go nowhere. The other...

The Processor is a ACS R1. Shouldn't the voicemail get it's time and date from the ACS? The voicemail anounces the default date/time of Jan 1 and 12am for all messages. info@ultimatecommunicationsinc.com www.ultimatecommunicationsinc.com

Is it possible to customize/change the transfer option avaialble to callers after leaving a message other than using the hard-coded *8? With the hard-coded procedure callers must press # after leaving the message then *8 followed by the extension number and # before transfer...

Had the same experience 3 weeks ago. My setup was IP406v2 / DS16v2 / ATM16 running R4.0 System would work fine as long as all calls inbound/outbound was on ports 1 thru 8 on the ATM16. Any calls through ports 9 thru 16 produced the results you described...had to do a hard reboot to clear the...

My IP Office 406V2(3.2)does not allow me to create a short code whether user,user rights or system that matches direclty with an extension number. I keep getting this error message " short code conflicts with user XXXX". I can save the config but the call does not follow the short code. This is...

I keep getting this system error whenever i boot my PC. WINDOWS - SYSTEM ERROR: object name already exists PC is running WinXP-home edition. I checked the event log and it gives the following: Soutce:Application Popup EventID:26 Category:None Can anyone give an idea of where to start in...

The Magix system will not allow renumbering with a leading zero. For a simple solution ask the provider to change the leading digit to anything except 7 / 8 / 9 / 0. This is assuming you have regular standard programming in thw switch. info@ultimatecommunicationsinc.com...

If its a PRI you can do some digit manipulation to route the incoming calls. Since there is no way to do digits manipulation with a regular T1 then you can consider the folowing option: 1)Renumber a calling group to match the digits coming down the T1. 2)Then make this calling group overflow to...

Option 1 is the correct option. You cannot change the hard coded system prompts. The voice mail will search the index according to how the user names were entered. If there is only one name that name will be used. Therefore enter both names with a comma between the names with the first entry...

Sorry Merlinman I took another look at your post and now see what you are saying...You are refering to DID range(20) versus extension range(30) not DID ciruits. My bad...I am truly sorry.

The quantity of DID circuits need not match the amount of stations on the switch. You just need to have sufficient DID paths from the telco to facilitate a reasonable call volume,in this case they can handle 20 inbound calls at once, which is good, since the outbound service is not dependent on...

I have done a number of paging across networks.It is usually done for paging within the same organization that are physically apart.I would not recommend it for outsiders since it can easily get out of control. There are 2 options available First method used is to put the CO port used for paging...

I have 3 text boxes on my form.labeled as follows Amount($) , Rate(%) and Returns($).By goal is to automatically display a value in the third box after any of the other two boxes are updated. For example if Amount has 100 and Rate is 25 then 125 will display in Returns.My goal is to be able to...

Any type of DID whether analog/digital can be manipulated on the Magix/Legend. In this case strip 21 and append 2....or change the dial plan which is usually the way to go.