Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by New2Telco

  1. New2Telco

    Night auto attendant help!

    Definity R013x.01.2.632.1 I am able to run the command and I will research more on how to configure it. Thanks for your help.
  2. New2Telco

    Night auto attendant help!

    We have one of our remote locations setup with a night service extension in the "trunk-group" so when the receptionist presses the "trunk-ns" button all the incoming calls go to the Night AA announcement. However this location is requesting that calls coming to DID numbers go straight to the...
  3. New2Telco

    Feature buttons relabeling

    Thanks guys, the abbreviated system-list was the solution. Our system did not have a label for this button, so I assigned one and worked. I'm very glad to be on this forum, I'm learning a lot and I hope to be of help to others in the future.
  4. New2Telco

    Feature buttons relabeling

    Hello, We have been deploying 4620, 4621 IP phones in our company and the feature button assigned to dial the Audix extension to check the voicemail appears as "AD 8" for Abreviated-dial 8. I would like to rename this button "Voicemail" but I have not find a way to do it. I found the option on...
  5. New2Telco

    Analog ports assigned to Audix question

    Thanks again for your valuable help.
  6. New2Telco

    Analog ports assigned to Audix question

    Thanks Mitch for the information. When I called the extension assigned to that port rings three times then goes to the Audix message, but when I move it to a different port it keeps ringing and never goes to Audix. am I missing something?
  7. New2Telco

    Analog ports assigned to Audix question

    Hello all, In my company we have a total of 12 analog boards, but we have upgraded many of our phones to digital and IP.For the total number of analog lines we have we only needs 5 boards, so I'm trying to consolidate moving all the ports to these five boards. I've been able to clear 7 analog...
  8. New2Telco

    Easiest way to find disconnected ports

    Typing the code number worked! Thanks a lot guys, this is going to save me a lot of time.
  9. New2Telco

    Easiest way to find disconnected ports

    When I hit enter I get to a screen that says: ERROR REPORT The following options control which errors will be displayed. ERROR TYPES Error type: ______ The rest of the options are also blank. It looks like a "change" screen where you can make changes.
  10. New2Telco

    Easiest way to find disconnected ports

    I guess we do not have error reports enabled. All I see when I type "displ err" is the blank form to configure the error type I want to monitor.
  11. New2Telco

    Easiest way to find disconnected ports

    Hello, I need to make an inventory of how many ports (analog and digital) we are using and how many are disconnected in our main office. So far the only way I know is looking at the status of each station but I am trying to avoid that route. Is there any way to run a report or a list of stations...
  12. New2Telco

    CMS automatic reports question

    Hello, I'm trying to help with CMS administration at my company. We have a small call center and there are a couple of reports that print automatically each morning, but they need to be modified. I don't know what is trigering these reports to print automatically and if it's possible to modify...
  13. New2Telco

    How to find the DID to station information

    Thanks all for your answers they were relly helpfull.
  14. New2Telco

    How to find the DID to station information

    Hello, I am trying to find a commmand that can show me the DID#s associated to stations, but I don't know if there is such a command. Thanks.
  15. New2Telco

    EC500 feature questions from a newbie

    I was able to see the licenses information with the "display capacity" command. I also used the "add off-pbx-tel stat" command. Finally from one of the phones I dialed: FAC#Extension#Securitycode# and heard a 3 beep confirmation signal. Thanks for your help, it lead me in the right direction.
See more

Part and Inventory Search

Back
Top