Recent content by isokocons

this is more updates....any help,tip will be appreciated. the board is defined in 'change data-mod' display data-mod 3801 Data Extension: 3801 Name:CLAN1 Type: ethernet Port: 01A1517 Link: 1 display ip-services service Enabled Local...

update.... I checked my alarms... display alarms PN 01 PKT-BUS y Major n 03/18/09:19 01A1532 SYS-LINK n RSCL WARNING 03/18/09:17 01A1632 SYS-LINK n RSCL WARNING 03/18/09:17 list sys-link... 01A1632 RSCL down none default 01A1532 RSCL down none default Given that my C-LANs are on slots A15 &...

ii8206, Were you able to resolve your problem? I am having the same problem with my new setup. I can ping the IP Media processors but cannot ping anu of the C-LANs. The IP Media processor, C-LANs, and some PCs are on the same VLAN, same subnet but only the IP media processor can be pinged...

I have not statrted programming the analog or the digital ports at this time. We really might not need until in the distant future, we have IP-phones, bringing these IP Phones up is my primary concern now. I have or think I have fully configured the C-LAN interfaces, but maybe I am missing...

Hi all, I am trying to bring up the Definity ECS R10 switch. It have 2 C-LANs and 2 IP Media Processors. I have configured all 4 interfaces via 'change ip-interface', 'change ip-service', 'change node-name ip' and also configured 'link'. All boards are on the same VLAN and subnets, the LEDs...

Yes, the 6509 will be able to run from one power supply.

Thanks HmmG3 and Mike Jones, I will not have any problem putting each of the cards in their appropriate slot, because they were clearly labelled. Before I start worring about configuring the routing, dial plan, route patterns, etc. I want to be able to appropriately cable each of the various...

Hi All, Looking for some ideas, tips, suggestions, directions, etc. We have a Definity ECS Si telephone switch and Intuity Audix Model MAP/5P V3, these systems were deinstalled from one of our closed offices and they are currently in our warehouse. All the cards in the definity has been...

Thank You all for your contribution. I justed called Avaya and problem fixed! Old Page 2 (Ch hunt 1) config: 1st Announcement Ext: 76xx 2nd Announcement Delay(Sec): 0 1st Announcement Ext: 76xx 2nd Announcement Delay(Sec): 20 New Page 2 (Ch hunt 1) config: 1st Announcement Ext: 76xx 2nd...

The hunt group is queue. I checked the COR the hunt group belong to and it is set to allow music on hold to play. I called Avaya, I was told, it might not be possible for people on queue to hear music on hold, that the phone will be ringing until it is picked up or disconnected. The lady from...

I want to add that, I am not using vectoring in my hunt group. I will prefer a solution that will exclude vectoring. Note: My Music on hold is working fine. When calls are placed on hold, the music comes on. Thanks.

I have music on hold setup. It is working, but I want a situation where when some call the hunt group that I have created, and the call is but ob queue, the music on hold should start playing until the call is answered. How it work now is: When some call the hunt group number, the forced first...

Access list nat statement will accomplish that for you.

Do an 'ipconfig' or 'route print' on the clients. What is their default gateway. They might have obtained an ip address, what about a default gateway? The default gateway must be an ip address on the same network and subnet with the clients. The issue might just be that, when the clients ping...

access-list 101 permit ip 10.0.0.0 0.255.255.255 10.x.x.0 0.0.0.255 access-list 101 permit ip 10.0.0.0 0.255.255.255 10.x.y.0 0.0.0.255 In each of those statements, you will be having problem with overlapping. The destination address is a subnet of the source address. Am kind of curious what...