×
INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Students Click Here

How to set up DID on Norstar MICS 4.1 system
4

How to set up DID on Norstar MICS 4.1 system

How to set up DID on Norstar MICS 4.1 system

(OP)
I have set up a couple of new phones but have noticed that the DID's are not working on these new phones. I checked the settings of the phones with the working DID's and see no difference in the settings. Can anyone tell me what to check or do to get these lines to recieve direct inward dialing? I'm a little new to the system, so I may have missed something.
Thanks

RE: How to set up DID on Norstar MICS 4.1 system

3
Are you using T-1 or straight DID trunks?

MRoberts
mroberts@americaii.com
If you find a tip helpful, please mark it as such.

RE: How to set up DID on Norstar MICS 4.1 system

(OP)
I have a full T1
may change to PRI to get caller ID.

also is there a way to see which lines have which DID assignments o r do I have to go line by line?

RE: How to set up DID on Norstar MICS 4.1 system

Unfortunately you gotta go target line by target line. The following is the full set up of a T-1 so you can check everything. Just remember, when you change to PRI you have to use a route and destination code to make outgoing calls.How to Install a T1:

You must have either a Services Cartridge (slot 1) or a 6-port Combo card (slot 2) in order to provide clocking for the T-1. Only one of these is needed, even if you have two DTI cards.
The DTI card should go into Slot 4 first. If you have a second card it would go into Slot 3.
You must disable the card first, program the card for T1, then re-enable the card.

To Disable / Enable Card
From Terminals & Sets – Next until you get to
Maintenance – Show
Next until get to Module Status – Show
Show module – Next
KSU (1):  Next or State if using (2) cards
KSU (2):  State
( ) Ports Busy – Press Disable or Enable
Disable at Once? – Yes

Protocols & Signaling
Hardware – Show
Show Module – Next
Cards on KSU – Show
Cd1 – KSU:        
Change to T-1 – Show
Card Type T-1 – Next
Lines: 001-024 – Next
Protocol: SL1 – Next (check with your Telco Carrier for setting)
Type Slave – Next
Bchanseq: Ascend or Descend – Next (check with your Telco Carrier for setting)
CO Fail: TIA–547A – Next
IF Levels: ISDN – Next
Framing: ESF – Next (usually ESF, check with your Carrier
Internal CSU: ON – Next
{need to have either an external CSU or turn the internal one on. If customer needs to use some channels for data then they’ll need a CSU/DSU to split off channels before the 0X32. OR to split off data channels after 0X32 they’ll need a Nortel Data Interface (NDI) plus bandwidth allocation key codes}
DSX1 Bld: 000-100
Line Coding: B8ZS (usually B8ZS, check with the Carrier)
ClockSrc: Primary (second card would be secondary)

Re-enable the card in Maintenance now.

Channel Set Up
From Lines: - Show
Line001:Line001 – Show (you’re entering your channel numbers here. If you’re using                     straight DID cards, then you’ll begin with ‘line’ 049)
Trunk/Line data – Show
TrunkType: E&M – Next
Line type: Pool A - Next
Dial Mode: Tone – Next
PrimeSet: 221 – Next
Auto privacy: Y – Next
Ans Mode: Auto – Next
Ans with DISA: N – Next
Aux. Ringer: N – Next
Signal: WinkStart – Next
ANI number: N – Next
End of List

Target Lines Programming:
From Lines – Show
Show LN: 145 – Show (target line range from 145-275 non-XC SW, 145-336 XC SW)
Target LN – Next
Private to: (extension number) – Next
Rec’d #: (enter digits Telco is sending) – Next
If Busy: to prime – Next
PrimeSet: 221 change to the extension # - Next
CLID Set: None – Next
Aux. Ringer: N – Next
End of list


MRoberts
mroberts@americaii.com
If you find a tip helpful, please mark it as such.

RE: How to set up DID on Norstar MICS 4.1 system

Have you assigned the DID line number (i.e. line 145) to the DN?  If so, the dn should ring when you call the DID. Assuming you have relatively new software, you can check the line programming as follows.  Enter system programming and pres NEXT to go to Lines programming. Enter the line number for the DID and press SHOW twice.  You'll see "target line".  Press NEXT twice and you'll see the received digits for that line.  Press NEXT again to be sure that IF busy: is set "To prime".  Press NEXT and make sure the prime set is the correct DN.  Otherwise, a second call coming in will ring in the wrong place.  If you'd like, send me an email (patj@lazertel.com) and I can send you a cheat sheet.

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members! Already a Member? Login

Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close