×
INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Contact US

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Students Click Here

PRI error codes/dianostics

PRI error codes/dianostics

PRI error codes/dianostics

(OP)
I presently have been receiving the following error codes in the switch (61C..Rel25):
PRI 227 DCH:2 DATA:4
PRI 218 DCH:2 DATA:0

I have opened a ticket with my carrier since DCH:2 is my primary D-chnl with DCH:3 being it's backup in a 2PRI trunk group.

I was wondering if someone could assist with what the issue possibly could be with the protocol/signaling on the D-chnl.
Also what LD do I go to to review the D-Chnl info to ensure it did not change from DMS-250 as it was originally setup, and to allow me to change if not correct. I'm sure I would be down if this was the case. At the moment I am getting a lot of reorders when I see the errors stream across the screen.

Side question:
All of a sudden my term on TTY 1 can no longer TX to the switch. All I get on the screen are "L's" when I type. I checked all the settings on the term and they appear correct as they always have. I also swapped the term out with a new one...same results. I was wondering if someone has seen this if a TTY port goes bad. The Term can display the info coming from the switch though.

Thanks in advance...

RE: PRI error codes/dianostics

blameitonme,

To look at your DCH configs go to LD 22.

>ld 22

REQ  PRT

TYPE ADAN DCH

Look at the IFC prompt to see what protocol you have.  You can also get that info from LD 21.

>ld 21

REQ: PRT

TYPE: RDB

CUST 0

ROUT XXX

Once again look for the IFC prompt.  To change this prompt go to LD 17 and ld 16 I belive.

Also I would look at LD 96 and do a PLOG for yor DCH.

>LD 96

PLOG DCH XXX

You will then need to look in the NTP's for the explaination of your errors if any.

As far ad your TTY issue I would go to LD 37 an type in STAT and make sure TTY 1 is enabled.  If it is anabled go to LD 22 and PRT, ADAN TTY.  Make sure the settings are correct.  

Just curious what J port on the back of your M1 does your TTY 1 reside.  The reason I'm asking is that I'm having problems with a direct connect to my TTY 1 on J13 & it is a DB9 as where the others are a DB25.  If you know, or if any one else knows: what is the pin out for the DB9 on an M1.

RE: PRI error codes/dianostics

Just a thought are the DCH's and TTY port on the same MSDL card.

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members! Already a Member? Login


Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close