What LD to change DCH

[tomkuk]

Hi, I need to change some setting on a qsig circuit.

I know to print this in ld 22 but not sure how I go about chnaging any parameters?

Thanks,
Tom.

 

[tbonz25]

To make a change to a dchannel you need to do this in LD 17 the command is below. In some instances you have to out the dchannel and rebuild it to change certain parameters.

REQ:chg
TYPE:adan
ADAN:chg dch xx

 

[jdm5000]

I'm having an issue with my long distance calls so I'm trying to switch my 2 PRI loops that aren't working to the d-channels my 2 PRIs that do work are using as a test.

So far, I've figured out how to show my current setup, but I can't seem to figure out how to actually change it.

I'm trying to change PRI 13 and 29 to use the same d-channels as PRI 12 and 28. What commands would I use?

Here's what I have now:

>LD 22
PT2000

REQ PRT
TYPE CEQU

CEQU
MPED 8D
TERM
REMO
TERD 002
REMD
TERQ 003
REMQ
SUPL 004 020
SUPC
SUPF
XCT 000 016
TDS * 000 * 016
CONF * 001 * 017
MFSD * 000 * 016

DLOP NUM DCH FRM TMDI LCMT YALM TRSH
PRI 012 24 ESF NO B8S FDL 00
013 23 ESF NO B8S FDL 00
028 24 ESF NO B8S FDL 00
029 23 ESF NO B8S FDL 00
MISP
EXT0 3PE
CNI 012 000 000
EXT1 3PE
CNI 012 000 000
MCFN S0B0 S0B1 S1B0 S1B1 S2B0 S2B1 S3B0 S3B1 FLSH TOTL
016 000 016 016 016 016 000 000 64 144

 

[hawks]

You can not just change them without your Telco also changing their end. Right now it looks like you have 2 D-Channels (primary & backup) for each pair of PRI circuits. If you want all 4 on the same 2 D-Channels then you'll have out the 2 and rebuild them onto the D-Channels you want. Plus your Telco will have to move them to the same D-Channels.

 

[jdm5000]

We've just been switched from Sprint to AT&T so the D-Channels for PRI 13 and 29 no longer exist. Our Long Distance traffic is now supposed to route through the local trunk, but I can't get that to work.

I've looked in the RLI and the local truck route is set up as ENTR 1 for long distance calls (ENTR 0 being the now defunct Sprint route).

 

[jdm5000]

err.... local TRUNK route.. heh

 

[bhassell2000]

out the DCH and rebuld them and where it says PRI put the loop number you want them to be associated with, and it lloks like you are a large system so if these D channels are on a msdl card you will have to move the cables to the correct PRI card

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[jdm5000]

oh fun.

which LD would that be under?

 

[bhassell2000]

ld 22
prt
adan dch xx

to have a copy of what you have now then:

ld 17
req chg
type adan
out dch xx

req chg
type adan
new dch xx

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[jdm5000]

awesome.. Thank you kindly, good sir

 

[bhassell2000]

you will have to turn down the pris and might have to out the trunks in ld 14 before you can out the dch, you can print the TNB of a trunk in ld 20 and then

ld 14
req out 23
type xxxx probably tie or did
tn x x


Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell