Trying to install new T1 to Qwest LD Need Help 2

[acewarlock]

Here is the RDB

TYPE RDB
CUST 00
DMOD
ROUT 1
DES QWEST LD
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA YES
NCRD YES
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DCDR NO
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD 8001
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512
NBS 2048
NBL 4096
TFD 0
LEXT 100
DRNG NO
CDR NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

This is what I get when I try to program the trunks.

REQ new 24
TYPE cot
TN 6 1
DES QWEST LD
PDCA
PCML
CUST 0
NCOS
RTMB 1 1

SCH4788
RTMB

SCH4788
PRI loop is not configured with D-channel (DCHI) to provide
B-channels.

Severity: Info



How do I program a D-channel?

Thanks for any help

 

[johnpoole]

ld 73 for the ddb to set your clock, ld 60 stat cc0 stat cc1, to see the clock status

john poole
bellsouth business
columbia,sc

 

[acewarlock]

Option 11C
I have 3 other T1's for DID and out local and 1 for VOIP.

ld 60
DTI000
.stat cc0

.
DTI005
stat cc1

DTI005




LD 73
REQ prt
TYPE ddb

CC0 3
PREF CC0 3
SREF CC0 2

TRSH 00
RALM 3
BIPC 2
LFAC 3
BIPV 3 2
SRTK 5 30
SRNT 15 3
LFAL 17 511
SRIM 1
SRMM 2
ICS

 

[mluckie1]

try "SSCK 0" in ld 60.

 

[janchundia]

ld 60
.ssck 0 for option 11C

javier

 

[acewarlock]

ld 60
DTI000
.ssck 0
ENBL
CLOCK ACTIVE
CLOCK CONTROLLER - LOCKED TO SLOT 3
PREF - 3
SREF - 2
AUTO SWREF CLK - ENBL
NO ERROR

IP DB PORT 1 DSBL
IP DB PORT 2 DSBL
IP DB PORT 3 DSBL
IP DB PORT 4 DSBL
CABINET CLK SRC: CC

 

[hawks]

It looks like you already have a clock card in the system. If that's the case then you do not need one on this new T1.

 

[acewarlock]

So I should disreguard the Red CC LED?

 

[hawks]

You probably have a clock card (daughter board) on the new T1 card. What I would do is take it off and save it for a future use. This way your light will go away also.

 

[brewerdude]

If he's got a TMDI card, I believe it's built in.

 

[johnpoole]

yes, the red will stay on but you can't add add clocks, if you had a reason to clock off of the new card, then you'd need to delete the clock on 2 or 3 and put it back in on the new pri..

john poole
bellsouth business
columbia,sc

 

[hawks]

Clock still a daughter board the D-Channel is built in. Someone correct me if I'm wrong.

 

[brewerdude]

You are correct, from the NTP's:

The NTRB21 (DTI/PRI/DCH) TMDI digital trunk card is a 1.5 Mb DTI or
PRI interface to the Succession 1000, Succession 1000M Cabinet, and
Meridian 1 Option 11C Cabinet. The NTRB21 card has a built-in
downloadable D-channel.


The NTRB21 card uses a standard 9.5" by 12.5" multi-layer printed circuit
board with buried power and ground layers.The clock controller
daughterboard is fastened by standoffs and connectors.

 

[janchundia]

Only one clock you can use into the option 11C.
Then the option 11C syncronize with clock source and distribute in all systems including the other T1´s.
If you want to use the new clock reference, you need to disabled the other clock and switch off in this card.

 

[acewarlock]

TDMI card is NTRB21AC
daughter board is NTAK20AD

You mean I don't need the NTAK20AD daughter board?

 

[brewerdude]

Not if your other T-1's are providing clock (which sounds like your case).

 

[hawks]

One more note for future use if this is another PRI with the same carrier you don't need another D-Channel either. All you need is 2 PRI's running 1 as a Primary and 1 as a Back up D-Channel then you can add up to (some say 16) PRI's. I've only put 6 together.

 

[acewarlock]

I have 3 going to the same carrier Sprint, the first one is Primary and the 2nd is Backup. the new one is going to Qwest.

 

[hawks]

Need D-Channel then

 

[johnpoole]

pretty hard rule, you need at least one d for each route, and at least one route per carrier.. the d channel is set up and tear down for the b channels..along with much more.. with that said you can't send setup for a call over the quest pri to the sprint office... a little less fuzzy when you think of it that way

john poole
bellsouth business
columbia,sc