Trying to install new T1 to Qwest LD Need Help 2

[acewarlock]

Here is the RDB

TYPE RDB
CUST 00
DMOD
ROUT 1
DES QWEST LD
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA YES
NCRD YES
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DCDR NO
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD 8001
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512
NBS 2048
NBL 4096
TFD 0
LEXT 100
DRNG NO
CDR NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

This is what I get when I try to program the trunks.

REQ new 24
TYPE cot
TN 6 1
DES QWEST LD
PDCA
PCML
CUST 0
NCOS
RTMB 1 1

SCH4788
RTMB

SCH4788
PRI loop is not configured with D-channel (DCHI) to provide
B-channels.

Severity: Info



How do I program a D-channel?

Thanks for any help

 

[acewarlock]

PS This is an Option 11C rel 25.40B+.

 

[mluckie1]

Try and rebuild the route as DID or TIE. Is the DChannel built and is the loop defined in CEQU as PRI.

 

[brewerdude]

Dchannels are built in LD 17 as ADAN

also, if you're going to build multiple trunks using the NEW X command and have a d-channel, you'll only want to build 23 trunks.

Also - do you have the d-channel daughterboard on your T-1 card?

 

[Nortellian]

ditto on the new 23 command. Is quest suppling 23 channels and a D-channel or 24 channels. Depends on what you ordered.

 

[acewarlock]

I'm waiting to find out what was ordered. I though they were setting it up just like our other T1's.

 

[johnpoole]

if it's a pri, then you'll get 23 and a d, if it's a t1 you'll usually get 24 channels

john poole
bellsouth business
columbia,sc

 

[acewarlock]

OK I found out it's a PRI 23b +D, so I guess I need a
d-channel daughterboard. there end is a DMS250.

 

[johnpoole]

if you need help with the d config let me know, i'll post mine

john poole
bellsouth business
columbia,sc

 

[hawks]

If your going with NI2 protocol then you need the NTBK51BA for you D-Channel.

 

[johnpoole]

here's a copy of the d channel, route and trunk for a 250 interface that is working


ADAN DCH 157
CTYP MSDL
GRP 4
DNUM 15
PORT 1
DES BS_LD
USR PRI
DCHL 157
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC D250
SIDE USR
CNEG 1
RLS ID 33
RCAP
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7


TYPE RDB
CUST 00
ROUT 157
DES BSLD
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC D250
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 8380
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 1 *
NDNO 1
DEXT NO
DNAM NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096



PAGE 002

IENB 5
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST NO
QREC YES
OAL YES
AIA YES
OAN YES
OPD YES
CDRX NO

SCH2017

NATL NO
TDG
VRAT NO
MUS YES
MRT 10
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO


DES BSLD
TN 157 01
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 1
RTMB 157 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD HKD
P10 VNL
TKID
DATE 26 OCT 2004


john poole
bellsouth business
columbia,sc

 

[acewarlock]

Here is my RDB, ADAN DCH 11, TNB, STAT LD 60, Stat LD 96.

When I stat LD 60 the trunks in route 6 don't show up, but I can do a TRAC in LD 80 and they are there. What am I doing wrong?

Thanks for any help.




ADAN DCH 11
CTYP TMDI
CARD 06
PORT 1
DES QWESTLD
USR PRI
DCHL 6
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSERV NO




TYPE RDB
CUST 00
DMOD
ROUT 1
DES QWESTLD
TKTP DID
NPID_TBL_NUM 0
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA YES
NCRD YES
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG OGT
RANX NO
SRCH LIN
STEP
ACOD 8001
TCPP NO
TARG 01
CLEN 1
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DEXT NO
DNAM NO
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
TFD 0
CDR NO
MUS YES
MRT 9
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO



LD 20
TNB

DES QWEST LD
TN 006 01
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 1 1
B-CHANNEL SIGNALING
NITE
STRO OWK
AST NO
IAPG 0
CLS UNR DTN CND WTA LPR APN THFD HKD
P10 VNL
TKID
DATE 11 JAN 2005


LD 60
STAT

PRI* TRK LOOP 4 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE DID 3VCE * CH 02 - IDLE DID 3VCE *
CH 03 - IDLE DID 3VCE * CH 04 - IDLE DID 3VCE *
CH 05 - IDLE DID 3VCE * CH 06 - IDLE DID 3VCE *
CH 07 - IDLE DID 3VCE * CH 08 - IDLE DID 3VCE *
CH 09 - IDLE DID 3VCE * CH 10 - IDLE DID 3VCE *
CH 11 - IDLE DID 3VCE * CH 12 - IDLE DID 3VCE *
CH 13 - IDLE DID 3VCE * CH 14 - BUSY DID 3VCE *
CH 15 - IDLE DID 3VCE * CH 16 - BUSY DID 3VCE *
CH 17 - IDLE DID 3VCE * CH 18 - IDLE DID 3VCE *
CH 19 - IDLE DID 3VCE * CH 20 - IDLE DID 3VCE *
CH 21 - BUSY DID 3VCE * CH 22 - IDLE DID 3VCE *
CH 23 - BUSY DID 3VCE * CH 24 - BUSY DID 3VCE *

PRI* TRK LOOP 6 - DSBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
.

LD 96
.STAT DCH
DCH 003 : OPER EST STBY AUTO BKUP 004 DES : MAINDCH
DCH 004 : OPER EST SERV AUTO PRIM 003 DES : MAINDCH
DCH 010 : OPER EST ACTV AUTO DES : IPTRUNK
DCH 011 : DSBL RST AUTO DES : QWESTLD
.

 

[johnpoole]

PRI* TRK LOOP 6 - DSBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL..it shows up ace, it's just down, ld 60 enll 6...look for dta023...layer 1 passes, about 2 minutes later, you should see dch estblish...your in an 11, and if that is a tmdi card, you'll need to go to 96, 1st and do a enl tmdi 6 fdl...sdl 100 (good code)... takes a few min for the full down load..then do a stat tmdi, stat dch...you'll see that your dch is down.. can't be up. go to 60 and bring up the loop...d jumps up bye itself


john poole
bellsouth business
columbia,sc

 

[johnpoole]

btw, any change on the d, go to 96 and do the full down load again, the changes don't take effect without it..

john poole
bellsouth business
columbia,sc

 

[mluckie1]

on the rdb change the ICOG to IAO, in and out. If the Dchannel does not establish, confirm setup is NI2 and not D250 or D100 depending on your providers equipment.

 

[johnpoole]

ICOG to IAO...that's for two way trunks..in and out...the reason the d is not in 96 on the stat is because the fdl hasn't happened..the card doesn't have the changes you made on it

john poole
bellsouth business
columbia,sc

 

[mluckie1]

That Dchannel is in 96, look at the last dch 011. I would agree that the TMDI or the MSDL daughter board has to be downloaded after any changes to the dchannel. The iao will make it easier if you want to recieve inbound calls on the span, IDC is set to yes i'm guessing for inbound calls. The dchannel will stay at it's current state until the loop is enabled no matter how many times it is downloaded though. One other thing, I would disable and enable the tmdi card after the FDL command for some reason this helps the card to operate correctly. It should be Loop 6 in Route 1.

 

[acewarlock]

Thanks John, everything came up just like you said it would.

Thanks everyone

 

[acewarlock]

The T1 seems to be working OK, but I have a RED CC Led lit and I have a Green Led on ACT and DCH. is this a problem? Qwest hasn't officily turned the T1 up yet but I can make calls on it.

 

[brewerdude]

CC is for your Clock Controller. Did you configure one on the PBX?