Hello folks
I'm looking for a config file for a g430 or G450. (probably the same for all gateways with current firmware) I've pouned on this thing so hard I've nearly beat it flat. (just joking) In any case I figure the best way to get it working is to reference a known working configuration. My config is below.
Thanks
Richard
! version 30.15.0
Config info release 30.15.0 time "11:36:01 07 DEC 2010 " serial_number 09IS47290405
encrypted-username Tp86ljuCYVnIJDsuLLVJ+A== password erqz5I9nWKu+Zne9jYdzqx0qIZcn2yhz/JrINTYnurk= access-type TV2ScO1d8p7ahmbnF8agKQ==
encrypted-username nslEo2clzt0FnW9wz1e3EA== password xKwLupXRv283cXkcK9uKTGDZmC7ioTMMV4pETpZloSI= access-type h/f9JnxX4o172W54rbyQFA==
hostname "AZSURP01GTW01"
set system location
set system name
set system contact
set logging file enable
set logging file condition all Error
set logging file condition BOOT Debug
no ip telnet
encrypted-snmp-server community read-only G+ogKy3vd38GlV/2nw4AEw== read-write yNug1LYqWcThG8typPG4+uwt/puswmC8VQk1AGm8f8E=
set spantree disable
set port spantree disable 10/4
set port negotiation 10/3 disable
set port speed 10/3 100MB
set port name 10/3 "LAN 10/3"
set port classification 10/3 regular
set port negotiation 10/4 disable
set port speed 10/4 100MB
set port name 10/4 "LAN 10/4"
set port classification 10/4 regular
interface Vlan 1
icc-vlan
ip address 10.212.68.67 255.255.255.0
pmi
exit
interface FastEthernet 10/2
shutdown
exit
interface Dialer 1
dialer modem-interface USB-Modem
exit
interface USB-Modem
description "Default Modem Setup"
timeout absolute 10
ppp authentication ras
no shutdown
ip address 192.156.1.49 255.255.255.0
exit
ip default-gateway 10.212.68.1 1 low
set mgc list 10.221.57.10,10.221.57.12
set mediaserver 10.221.57.10 10.221.57.10 23 telnet
set mediaserver 10.221.57.10 10.221.57.10 5023 sat
set mediaserver 10.221.57.12 10.221.57.12 23 telnet
set mediaserver 10.221.57.12 10.221.57.12 5023 sat
set reset-times primary-search 2
set reset-times total-search 3
set reset-times transition-point 2
set sync interface primary v1
set sync source primary
rtp-stat qos-trap
no rtp-stat fault
sls
set slot-config v1 mm710
set slot-config v2 mm717
set slot-config v3 mm711
exit
sls
ds1 v1
set channel-numbering seq
set name "QWEST_PRI"
set protocol-version a
exit
exit
sls
sig-group 21
set trunk-group-chan-select 1
set primary-dchannel 021v124
exit
exit
sls
station 5465151 dcp
set cor unrestricted
set encrypted-password "kyGGVGNURtOHZNBCU2SUDQ=="
set port v201
set type dcp2420
exit
station 5465152 dcp
set cor unrestricted
set encrypted-password "t3hqTo400zAd14MgKSRx+g=="
set port v202
set type dcp2420
exit
station 5465153 dcp
set cor unrestricted
set encrypted-password "Oc7wrY/dekl5eBEtQyI1wA=="
set port v203
set type dcp2420
exit
station 5465154 dcp
set cor unrestricted
set encrypted-password "4GgZChb+xYxnocQWDUIqMA=="
set port v204
set type dcp2420
exit
station 5465155 dcp
set cor unrestricted
set encrypted-password "Z1pmkmp1CrJ4qGwbqMMEqw=="
set port v205
set type dcp2420
exit
station 5465156 dcp
set cor unrestricted
set encrypted-password "PxC3WKBNfxfJAbCzbwB1tQ=="
set port v206
set type dcp2420
exit
station 5465157 dcp
set cor unrestricted
set encrypted-password "CDAtjHwtuLf8SXatFy7e/A=="
set port v207
set type dcp2420
exit
station 5465158 dcp
set cor unrestricted
set encrypted-password "Gkm1R63JkF9AZxmI/dF83Q=="
set port v208
set type dcp2420
exit
station 5465159 dcp
set cor unrestricted
set encrypted-password "qgHQvj4e/mgDoawK9dl+PQ=="
set port v209
set type dcp2420
exit
station 5465160 dcp
set cor unrestricted
set encrypted-password "vDIbaUfJBNNAegXMwKsyGg=="
set port v210
set type dcp2420
exit
station 5465161 analog
set cor unrestricted
set port v306
exit
station 5465162 dcp
set cor unrestricted
set encrypted-password "AlmgmBORIcEoVH0crtc9vw=="
set port v212
set type dcp2420
exit
station 5465163 analog
set cor unrestricted
set port v307
exit
station 5465164 analog
set cor unrestricted
set port v305
exit
station 5465165 dcp
set cor unrestricted
set encrypted-password "8QgLkeR7l91d/5My7GnqhA=="
set port v215
set type dcp2420
exit
station 5465166 dcp
set cor unrestricted
set encrypted-password "796ZDOSG/FRm9CDBjXI6Xw=="
set port v216
set type dcp2420
exit
station 5465167 dcp
set cor unrestricted
set encrypted-password "0pJS4FViLQGPQv2fCzd/1A=="
set port v217
set type dcp2420
exit
station 5465168 dcp
set cor unrestricted
set encrypted-password "he5Aa6QjuL4tO+hxQuB6WQ=="
set port v218
set type dcp2420
exit
station 5465169 dcp
set cor unrestricted
set encrypted-password "gEbE6ExHJifq/8knrWWEEQ=="
set port v219
set type dcp2420
exit
station 5465170 dcp
set cor unrestricted
set encrypted-password "ysDD65SNyMM6syAElW74tQ=="
set port v220
set type dcp2420
exit
station 5465171 dcp
set cor unrestricted
set encrypted-password "lgAQMuTTF39HkdrpMRhoyA=="
set port v221
set type dcp2420
exit
station 5465172 dcp
set cor unrestricted
set encrypted-password "dULFcNaf7qjIMWWNqmXz5A=="
set port v222
set type dcp2420
exit
station 5465173 analog
set cor unrestricted
set port v308
set swhook-flash no
exit
station 5465174 analog
set cor unrestricted
set port v304
set swhook-flash no
exit
exit
sls
trunk-group 1 t1-isdn
set tac #88
add port v101 21
add port v102 21
add port v103 21
add port v104 21
add port v105 21
add port v106 21
add port v107 21
add port v108 21
add port v109 21
add port v110 21
add port v111 21
add port v112 21
add port v113 21
add port v114 21
add port v115 21
add port v116 21
add port v117 21
add port v118 21
add port v119 21
add port v120 21
add port v121 21
add port v122 21
add port v123 21
set trunk-hunt descend
set name "Qwest PRI"
exit
exit
sls
dial-pattern 1
set max-length 11
set min-length 11
set tgnum 1
set type fnpa
exit
dial-pattern 11
set insert-digits 9
set tgnum 1
exit
dial-pattern 1623
set max-length 11
set min-length 11
set tgnum 1
set type hnpa
exit
dial-pattern 1900
set deny yes
set max-length 11
set min-length 11
set tgnum 1
set type fnpa
exit
dial-pattern 480
set max-length 10
set min-length 10
set tgnum 1
set type locl
exit
dial-pattern 602
set max-length 10
set min-length 10
set tgnum 1
set type locl
exit
dial-pattern 623
set max-length 10
set min-length 10
set tgnum 1
set type locl
exit
dial-pattern 911
set tgnum 1
exit
exit
sls
incoming-routing 1 enbloc 5 4
set insert-digits 546
exit
incoming-routing 1 enbloc 5 7
exit
incoming-routing 1 enbloc 6 10
exit
exit
sls
set fac ars1 9
exit
set sls enable
analog-test
exit
!#
!# End of configuration file. Press Enter to continue.
PS, You can edit out any customer identifying information first.
I'm looking for a config file for a g430 or G450. (probably the same for all gateways with current firmware) I've pouned on this thing so hard I've nearly beat it flat. (just joking) In any case I figure the best way to get it working is to reference a known working configuration. My config is below.
Thanks
Richard
! version 30.15.0
Config info release 30.15.0 time "11:36:01 07 DEC 2010 " serial_number 09IS47290405
encrypted-username Tp86ljuCYVnIJDsuLLVJ+A== password erqz5I9nWKu+Zne9jYdzqx0qIZcn2yhz/JrINTYnurk= access-type TV2ScO1d8p7ahmbnF8agKQ==
encrypted-username nslEo2clzt0FnW9wz1e3EA== password xKwLupXRv283cXkcK9uKTGDZmC7ioTMMV4pETpZloSI= access-type h/f9JnxX4o172W54rbyQFA==
hostname "AZSURP01GTW01"
set system location
set system name
set system contact
set logging file enable
set logging file condition all Error
set logging file condition BOOT Debug
no ip telnet
encrypted-snmp-server community read-only G+ogKy3vd38GlV/2nw4AEw== read-write yNug1LYqWcThG8typPG4+uwt/puswmC8VQk1AGm8f8E=
set spantree disable
set port spantree disable 10/4
set port negotiation 10/3 disable
set port speed 10/3 100MB
set port name 10/3 "LAN 10/3"
set port classification 10/3 regular
set port negotiation 10/4 disable
set port speed 10/4 100MB
set port name 10/4 "LAN 10/4"
set port classification 10/4 regular
interface Vlan 1
icc-vlan
ip address 10.212.68.67 255.255.255.0
pmi
exit
interface FastEthernet 10/2
shutdown
exit
interface Dialer 1
dialer modem-interface USB-Modem
exit
interface USB-Modem
description "Default Modem Setup"
timeout absolute 10
ppp authentication ras
no shutdown
ip address 192.156.1.49 255.255.255.0
exit
ip default-gateway 10.212.68.1 1 low
set mgc list 10.221.57.10,10.221.57.12
set mediaserver 10.221.57.10 10.221.57.10 23 telnet
set mediaserver 10.221.57.10 10.221.57.10 5023 sat
set mediaserver 10.221.57.12 10.221.57.12 23 telnet
set mediaserver 10.221.57.12 10.221.57.12 5023 sat
set reset-times primary-search 2
set reset-times total-search 3
set reset-times transition-point 2
set sync interface primary v1
set sync source primary
rtp-stat qos-trap
no rtp-stat fault
sls
set slot-config v1 mm710
set slot-config v2 mm717
set slot-config v3 mm711
exit
sls
ds1 v1
set channel-numbering seq
set name "QWEST_PRI"
set protocol-version a
exit
exit
sls
sig-group 21
set trunk-group-chan-select 1
set primary-dchannel 021v124
exit
exit
sls
station 5465151 dcp
set cor unrestricted
set encrypted-password "kyGGVGNURtOHZNBCU2SUDQ=="
set port v201
set type dcp2420
exit
station 5465152 dcp
set cor unrestricted
set encrypted-password "t3hqTo400zAd14MgKSRx+g=="
set port v202
set type dcp2420
exit
station 5465153 dcp
set cor unrestricted
set encrypted-password "Oc7wrY/dekl5eBEtQyI1wA=="
set port v203
set type dcp2420
exit
station 5465154 dcp
set cor unrestricted
set encrypted-password "4GgZChb+xYxnocQWDUIqMA=="
set port v204
set type dcp2420
exit
station 5465155 dcp
set cor unrestricted
set encrypted-password "Z1pmkmp1CrJ4qGwbqMMEqw=="
set port v205
set type dcp2420
exit
station 5465156 dcp
set cor unrestricted
set encrypted-password "PxC3WKBNfxfJAbCzbwB1tQ=="
set port v206
set type dcp2420
exit
station 5465157 dcp
set cor unrestricted
set encrypted-password "CDAtjHwtuLf8SXatFy7e/A=="
set port v207
set type dcp2420
exit
station 5465158 dcp
set cor unrestricted
set encrypted-password "Gkm1R63JkF9AZxmI/dF83Q=="
set port v208
set type dcp2420
exit
station 5465159 dcp
set cor unrestricted
set encrypted-password "qgHQvj4e/mgDoawK9dl+PQ=="
set port v209
set type dcp2420
exit
station 5465160 dcp
set cor unrestricted
set encrypted-password "vDIbaUfJBNNAegXMwKsyGg=="
set port v210
set type dcp2420
exit
station 5465161 analog
set cor unrestricted
set port v306
exit
station 5465162 dcp
set cor unrestricted
set encrypted-password "AlmgmBORIcEoVH0crtc9vw=="
set port v212
set type dcp2420
exit
station 5465163 analog
set cor unrestricted
set port v307
exit
station 5465164 analog
set cor unrestricted
set port v305
exit
station 5465165 dcp
set cor unrestricted
set encrypted-password "8QgLkeR7l91d/5My7GnqhA=="
set port v215
set type dcp2420
exit
station 5465166 dcp
set cor unrestricted
set encrypted-password "796ZDOSG/FRm9CDBjXI6Xw=="
set port v216
set type dcp2420
exit
station 5465167 dcp
set cor unrestricted
set encrypted-password "0pJS4FViLQGPQv2fCzd/1A=="
set port v217
set type dcp2420
exit
station 5465168 dcp
set cor unrestricted
set encrypted-password "he5Aa6QjuL4tO+hxQuB6WQ=="
set port v218
set type dcp2420
exit
station 5465169 dcp
set cor unrestricted
set encrypted-password "gEbE6ExHJifq/8knrWWEEQ=="
set port v219
set type dcp2420
exit
station 5465170 dcp
set cor unrestricted
set encrypted-password "ysDD65SNyMM6syAElW74tQ=="
set port v220
set type dcp2420
exit
station 5465171 dcp
set cor unrestricted
set encrypted-password "lgAQMuTTF39HkdrpMRhoyA=="
set port v221
set type dcp2420
exit
station 5465172 dcp
set cor unrestricted
set encrypted-password "dULFcNaf7qjIMWWNqmXz5A=="
set port v222
set type dcp2420
exit
station 5465173 analog
set cor unrestricted
set port v308
set swhook-flash no
exit
station 5465174 analog
set cor unrestricted
set port v304
set swhook-flash no
exit
exit
sls
trunk-group 1 t1-isdn
set tac #88
add port v101 21
add port v102 21
add port v103 21
add port v104 21
add port v105 21
add port v106 21
add port v107 21
add port v108 21
add port v109 21
add port v110 21
add port v111 21
add port v112 21
add port v113 21
add port v114 21
add port v115 21
add port v116 21
add port v117 21
add port v118 21
add port v119 21
add port v120 21
add port v121 21
add port v122 21
add port v123 21
set trunk-hunt descend
set name "Qwest PRI"
exit
exit
sls
dial-pattern 1
set max-length 11
set min-length 11
set tgnum 1
set type fnpa
exit
dial-pattern 11
set insert-digits 9
set tgnum 1
exit
dial-pattern 1623
set max-length 11
set min-length 11
set tgnum 1
set type hnpa
exit
dial-pattern 1900
set deny yes
set max-length 11
set min-length 11
set tgnum 1
set type fnpa
exit
dial-pattern 480
set max-length 10
set min-length 10
set tgnum 1
set type locl
exit
dial-pattern 602
set max-length 10
set min-length 10
set tgnum 1
set type locl
exit
dial-pattern 623
set max-length 10
set min-length 10
set tgnum 1
set type locl
exit
dial-pattern 911
set tgnum 1
exit
exit
sls
incoming-routing 1 enbloc 5 4
set insert-digits 546
exit
incoming-routing 1 enbloc 5 7
exit
incoming-routing 1 enbloc 6 10
exit
exit
sls
set fac ars1 9
exit
set sls enable
analog-test
exit
!#
!# End of configuration file. Press Enter to continue.
PS, You can edit out any customer identifying information first.