Setting up VPN 4 the First time, Lost !!!!

[FWHATER]

I have Cisco VPN client 4.6, but am totally clueless as to configuring pix to act as the vpn server. I ran a few commands but do not want to resort to using PDM. I know I may need crypto map and acl's. I just need to be pointed in the right direction. Here's my config:

PIX Version 6.3(4)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 15Rw3oNAQ0RnJh5A encrypted
passwd 15Rw3oNAQ0RnJh5A encrypted
hostname FWHATER
domain-name FWHATER.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
name 10.x.x.x FWHATER2
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside dhcp setroute
ip address inside 10.x.x.x 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm location FWHATER2 255.255.255.255 inside
pdm location 0.0.0.20 255.255.255.255 inside
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 10.x.x.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet 10.x.x.0 255.255.255.0 inside
telnet 0.0.0.20 255.255.255.255 inside
telnet FWHater2 255.255.255.255 inside
telnet timeout 30
ssh timeout 5
console timeout 0
username FWHATER password ZDqjhX9RgPdeF9um encrypted privilege 2
vpnclient server 192.168.3.4
vpnclient vpngroup Hawkeyes password ********
terminal width 80
Cryptochecksum:3317e52eb0d0b9cf4e2fafc84ddfc650
: end

Thanx !!!

 

[FWHATER]

I've done some research and have made some changes to my last config, but still no luck. I'm coming in from the outside over the internet trying to get a response from the pix vpn server. Here's what I've got:

PIX Version 6.3(4)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 15Rw3oNAQ0RnJh5A encrypted
passwd 15Rw3oNAQ0RnJh5A encrypted
hostname FWHATER
domain-name ciscopix.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list 101 permit ip 10.20.30.0 255.255.255.0 host 0.0.0.0
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside dhcp setroute retry 4
ip address inside 10.20.30.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool freedom 172.20.30.1-172.20.30.10 mask 255.255.255.0
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list 101
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 10.20.30.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
crypto ipsec transform-set Power esp-3des
crypto dynamic-map freedom 10 match address 101
crypto map freedom 10 ipsec-isakmp dynamic freedom
isakmp keepalive 20
isakmp policy 1 authentication pre-share
isakmp policy 1 encryption 3des
isakmp policy 1 hash sha
isakmp policy 1 group 2
isakmp policy 1 lifetime 3600
vpngroup Skyhawks address-pool Freedom
vpngroup Skyhawks dns-server 10.20.30.3
vpngroup Skyhawks default-domain melodik.com
vpngroup Skyhawks idle-time 1800
vpngroup Skyhawks secure-unit-authentication
vpngroup Skyhawks password ********
vpngroup address-pool idle-time 1800
vpngroup freedom idle-time 1800
vpngroup Skyhawks idle-time 1800
vpngroup Skyhawks user-idle-timeout 60
telnet 10.20.30.0 255.255.255.0 inside
telnet timeout 60
ssh 10.20.30.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
username Madison password ZDqjhX9RgPdeF9um encrypted privilege 2
vpnclient server 10.20.30.1
vpnclient mode network-extension-mode
vpnclient vpngroup Skyhawks password ********
terminal width 80
Cryptochecksum:b1e41bcded838a6d1ef216d3866d0a88
: end

 

[boymarty24]

Well you should start all over again.

Here is a good link from cisco´s page.

http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080093f6a.shtml

Replace des with the encryption standard you want to use.
You might want to add nat-traversal support.

 

[boymarty24]

Sorry for the link, was not the one i thought. Check this one instead.

http://www.cisco.com/en/US/products/sw/secursw/ps2308/prod_configuration_examples_list.html

 

[FWHATER]

I've actually gotten it to work, through sheer persistence and using PDM. One thing though, it only works in one direction. I can ping, access data and telnet to the vpn client. But the client can't get past the outside interface. I checked the log for PDM and found out I need a translation group, I guess to translate the addressess in the ip pool into the address range on the inside or protected network. Any thoughts ?

Thanx.

 

[FWHATER]

Thanks boyMarty24. That first config did the trick. VPN works in both directions. YAHOOO !!!!!