Hey all,
It was suggested on xp pro forum, I post this here.
I have a fujitsu, laptop, ht 3.2, 800 fsb,
1 gig of factory installed ram. Ran great
for first 3 mos. , now crashes constantly -
bsod.
8 hour memory tests showed all clear.
here are what look like the most pertinent
warnings after running sandra.
( some benchmarks crashed it ) This is my
ht 3.2 laptop I'm having so much trouble with.
800 fsb.
---------------
Warning 2533 : Disabled host controllers are present. Check BIOS settings.
Warning 2507 : Mainboard has too few memory slots. Upgrading the memory may be difficult or expensive.
Warning 2508 : All memory slots are full. Upgrading the memory may be difficult or expensive.
Warning 100 : Large memory sizes should be made of Registered/Buffered memory.
]]]]]]]]]]]]]]
Warning W2533 - The system has host controllers that have not been enabled by the BIOS/OS.
The BIOS does not support the Enhanced Disk Drive Specification. You may not be able to use the latest disk drives and technologies (e.g. 4-8GB and larger).
Fix: Try to upgrade (flash) the BIOS if possible. Check whether a BIOS update is available from your main board/PC manufacturer.
Warning 1206 - Device latency is high - the higher the latency, the more data a device can transfer in one go. The device may be hogging the bus for too long.
Warning W3101 - Power management is enabled. For desktops this is best to be disabled. If it is enabled, it may cause the drive to go into a low power/performance state or turn off.
Notice N5406 - System bandwidth appears to be memory limited. Generally this means that memory bandwidth is < 50% FSB bandwidth, thus CPU is starved. This generally indicates a mismatch between memory and system. Note that this does not indicate that memory timings are wrong, but the memory itself is slow.
]]]]]]]]]]]]
NOTE comments"
The bios on this is pretty simple. I don't
see any host controllers in there. I dont see
any latency settings either.
thanks alot,
Beth
It was suggested on xp pro forum, I post this here.
I have a fujitsu, laptop, ht 3.2, 800 fsb,
1 gig of factory installed ram. Ran great
for first 3 mos. , now crashes constantly -
bsod.
8 hour memory tests showed all clear.
here are what look like the most pertinent
warnings after running sandra.
( some benchmarks crashed it ) This is my
ht 3.2 laptop I'm having so much trouble with.
800 fsb.
---------------
Warning 2533 : Disabled host controllers are present. Check BIOS settings.
Warning 2507 : Mainboard has too few memory slots. Upgrading the memory may be difficult or expensive.
Warning 2508 : All memory slots are full. Upgrading the memory may be difficult or expensive.
Warning 100 : Large memory sizes should be made of Registered/Buffered memory.
]]]]]]]]]]]]]]
Warning W2533 - The system has host controllers that have not been enabled by the BIOS/OS.
The BIOS does not support the Enhanced Disk Drive Specification. You may not be able to use the latest disk drives and technologies (e.g. 4-8GB and larger).
Fix: Try to upgrade (flash) the BIOS if possible. Check whether a BIOS update is available from your main board/PC manufacturer.
Warning 1206 - Device latency is high - the higher the latency, the more data a device can transfer in one go. The device may be hogging the bus for too long.
Warning W3101 - Power management is enabled. For desktops this is best to be disabled. If it is enabled, it may cause the drive to go into a low power/performance state or turn off.
Notice N5406 - System bandwidth appears to be memory limited. Generally this means that memory bandwidth is < 50% FSB bandwidth, thus CPU is starved. This generally indicates a mismatch between memory and system. Note that this does not indicate that memory timings are wrong, but the memory itself is slow.
]]]]]]]]]]]]
NOTE comments"
The bios on this is pretty simple. I don't
see any host controllers in there. I dont see
any latency settings either.
thanks alot,
Beth