Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations wOOdy-Soft on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Router is undergoing a cold start 1

Status
Not open for further replies.
limejudo

limejudo

Technical User
Aug 4, 2004
110
US
My router always reboot, well this is what the guy is telling me in Ny and I'm in Lousiana.

When I do a sh logg it say my router did a cold start.
I'm using ver 12.3 (9a) with 64 dram and 16 flash. This location uses dsl as primary and isdn as a backup.

The guy states it not a power issue in the store. Has any other I.T cats came across something like this

Eric - A+, Net+, INet+ CCNA next week.
Network Admin/Helpdesk II
 
Sort by date Sort by votes
Its probably an SNMP cold start. These are not errors but informational messages. These only get displayed while the router is booting.

I think this is not the reason or an indication of the problem. The real problem is still alluding you. :)

hexn.gif
 
Upvote 0 Downvote
If you do a show version it should tell you how long the router has been up . Then you can tell if it is really rebooting or you are losing power , or you have the router plugged into a outlet that gets shut off everynight or the cleaners are pulling the plug to use it etcc.. :)
 
Upvote 0 Downvote
WEll, it just rebooted about 30 minutes ago and I get the same thing. I have another tech going out there to check power.

Eric - A+, Net+, INet+ CCNA next week.
Network Admin/Helpdesk II
 
Upvote 0 Downvote
I had once this problem due router overheating. Anyway show version will display reason for reboot.
Dulem
 
Upvote 0 Downvote
The reason is always system restart....Why is my stuff restarting. The system restart means either someone powercycle the machine or it was unpluged and replugged.

Please correct me if I'm wrong

Eric - A+, Net+, INet+ CCNA next week.
Network Admin/Helpdesk II
 
Upvote 0 Downvote
Can you post show version output?
Dulem
 
Upvote 0 Downvote
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK9O3S3-M), Version 12.3(10), RELEASE SOFTWARE (fc
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Tue 17-Aug-04 05:11 by kellythw
Image text-base: 0x80008098, data-base: 0x819E9FE4

ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

uptime is 5 hours, 11 minutes
System returned to ROM by power-on
System restarted at 11:22:18 EST5EDT Fri Nov 5 2004
System image file is "flash:c2600-ik9o3s3-mz.123-10.bin"


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco 2610 (MPC860) processor (revision 0x203) with 61440K/4096K bytes of memory.
Processor board ID JAD041504R2 (2958905015)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
1 ISDN Basic Rate interface(s)
1 ATM network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102


It's currently plugged into the ups.

Eric - A+, Net+, INet+ CCNA next week.
Network Admin/Helpdesk II
 
Upvote 0 Downvote
If you have a faulty ups power supply this could cause your problem , it is saying it up by power on like it lost power . I have seen where if the ups is faulty it causes this type problem , have it checked .
 
Upvote 0 Downvote
YOu know the ups does beep and it is having problems. But eh guy told me that it still have problem when it's plugged into the wall

Eric - A+, Net+, INet+ CCNA next week.
Network Admin/Helpdesk II
 
Upvote 0 Downvote
Perhaps you have problem with power from wall NOT ups.
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

jobsp90
  • Question
I have a issue in my office hospital network regarding using IPPBX software.
Replies
2
Views
238
DavetheChef
DavetheChef
CPM86
  • Question
Cisco isr 4331 with IOS and sip busy fail over to 2nd sip number on pbx?
Replies
0
Views
316
CPM86
CPM86
WinstonCH
  • Locked
  • Helpful tip
What is wrong with the diagram, there are people who will help to fix it? How do i do the configurat 1
Replies
1
Views
682
BIS
BIS
quazimotto
  • Locked
  • Question
Cisco ASA_5505 VPN to Juniper_SRX210 VPN IS UP_ No Traffic!!!!!!
Replies
0
Views
243
quazimotto
quazimotto
inlsp05
  • Locked
  • Question
2811 ios start with cf
Replies
0
Views
272
inlsp05
inlsp05

Part and Inventory Search

Sponsor

Back
Top