Required hardware for CCM using with PSTN line 2

[kam72]

Dear Expertise

Can anyone let me know how to connect local telophone line to CCM. What are the hardware required.

What i want if some make a call to my land line it will connect to my cisco IP phones rather than connecting to my normal phone.

Waiting for reply
Thanks

 

[kam72]

Thank you very much. I will do that. I appreciate your time and assistance.

Thanks PNDSCM and everyone

 

[kam72]

Hi

Eventually i have purchased
Cisco Router 2620
NM-2V
Vic-2fxo Card
============================================================
Can you please let me know how to configure the gateway to use PSTN line with my SCCP Phones which is already registered with call manager 4.1.2
============================================================
Please provide me step by step procedure to confiure it as you know i am new to cisco.


Thanks

 

[MG2005]

Heres what my 2621XM looks like

wherever you see "XXXXXX" you need to add your callmanager Ip addresses, etc, i described most of teh field inputs needed for you

Building configuration...

Current configuration : 5275 bytes
!
! Last configuration change at 23:47:48 EST Tue Aug 9 2005
! NVRAM config last updated at 23:48:04 EST Tue Aug 9 2005
!
version 12.3
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
service password-encryption
!
hostname XXXXXXXXXXX
!
boot-start-marker
boot-end-marker
!
logging buffered 4096 informational
no logging console
enable secret
!
no network-clock-participate slot 1
no network-clock-participate wic 0
aaa new-model
!
!
ip subnet-zero
ip cef
!
!
!
!
no ip domain lookup
no ftp-server write-enable
voice-card 1
!
!
!
!
!
!
!
!
!
!
!
!
!
ccm-manager fallback-mgcp
ccm-manager redundant-host XXXXX (= CCM IP address)
ccm-manager mgcp
ccm-manager music-on-hold
ccm-manager config server XXXXX (= CCM IP ADDRESS)
ccm-manager config
!
!
!
!
interface FastEthernet0/0
description XXXXXXXX
ip address XXXXXXXX
no ip proxy-arp
ip route-cache flow
speed 100
full-duplex
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
ip classless
ip route 0.0.0.0 0.0.0.0 XXXXXXX
no ip http server
!
control-plane
!
voice-port 1/0/0
timing hookflash-out 50
timing inter-digit 100
!
voice-port 1/0/1
timing hookflash-out 50
timing inter-digit 100
!
voice-port 1/0/2
timing hookflash-out 50
timing inter-digit 100
!
voice-port 1/0/3
timing hookflash-out 50
timing inter-digit 100
!
mgcp
mgcp call-agent XXXXXXX ( = CCM IP) 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp modem passthrough voip redundancy
mgcp package-capability mf-package
mgcp package-capability rtp-package
no mgcp package-capability res-package
mgcp package-capability sst-package
no mgcp package-capability fxr-package
mgcp default-package trunk-package
no mgcp timer receive-rtcp
mgcp timer net-cont-test 3000
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
!
mgcp profile default
!
!
!
dial-peer cor custom
!
!
!
dial-peer voice 1 pots
application mgcpapp
port 1/0/0
!
dial-peer voice 2 pots
application mgcpapp
port 1/0/1
!
dial-peer voice 3 pots
application mgcpapp
port 1/0/2
!
dial-peer voice 4 pots
application mgcpapp
port 1/0/3
!
dial-peer voice 999100 pots
application mgcpapp
port 1/0/0
!
dial-peer voice 999101 pots
application mgcpapp
port 1/0/1
!
dial-peer voice 999102 pots
application mgcpapp
port 1/0/2
!
dial-peer voice 999103 pots
application mgcpapp
port 1/0/3
!
line con 0
exec-timeout 5 0
password XXXXXXXXXXX
line aux 0
exec-timeout 5 0
password XXXXXXXXXX
no exec
line vty 0 4
exec-timeout 0 0
timeout login response 75
password XXXXXXXXXXXXX
transport preferred none
transport input telnet
!
ntp clock-period 17208258
ntp access-group peer 10
ntp server XXXXXXXXXXXXX
!
end

 

[kam72]

Thank you MG2005.

I followed your instructions, but facing one problem when i type MGCP command on router i am getting the following error.
=====================================================
melb(config)#mgcp
^
% Invalid input detected at '^' marker.

melb(config)#
=====================================================
What could be the reason? Is that because of current IOS version which i am using
Here is my cisco router show verion
=======================================================
melb#sh version

Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IS-M), Version 12.1(5), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Wed 25-Oct-00 11:43 by cmong
Image text-base: 0x80008088, data-base: 0x80CAC644

ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

melb uptime is 1 hour, 7 minutes
System returned to ROM by power-on
System image file is "flash:c2600-is-mz_121-5"

cisco 2620 (MPC860) processor (revision 0x102) with 53248K/12288K bytes of memor
y.
Processor board ID JAD042701EE (1286926306)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
4 Voice FXO interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102
melb#
============================================================
If you believe that i am using incorrect version to configure the gateway. Then which IOS version do i require and from where i can get the new IOS Version. I donot have additional access with cisco as i cannot download the new IOS version from cisco website.
============================================================Please help me thanks mg2005

Thanks For your reply

 

[pndscm]

I use c2600-is-mz.122-29.bin for my 2620's and it works fine. Don't know where you'd get it if you don't have CCO access. You could try building the gateway as an H.323 gateway. More configuration but if it's all you've got......Probably can get a complete sample config from Cisco.com. Try this as a starting place:

http://www.cisco.com/en/US/products...s_configuration_example09186a0080094852.shtml

 

[MG2005]

http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a008017787b.shtml

looking for some info for you based on your IOS release 12.1(5). Per above link it looks liek it supports MGCP but may require a different configuration than my release does

 

[kam72]

I tried that its not accepting MGCP command. What should i do?

 

[pndscm]

If you don't have CCO access to get the IOS, build it as an H323 gateway as I mentioned before. You don't have any other option.

 

[kam72]

Hi PNDSCM

I have followed your instruction. The router is not accepting even h323 command.
"% Invalid input detected at '^' marker."
============================================================
Here is the show version of my router
============================================================
gateway#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IS-M), Version 12.1(5), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Wed 25-Oct-00 11:43 by cmong
Image text-base: 0x80008088, data-base: 0x80CAC644
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
gateway uptime is 11 minutes
System returned to ROM by power-on
System image file is "flash:c2600-is-mz_121-5"
cisco 2620 (MPC860) processor (revision 0x102) with 53248K/12288K bytes of memory.
Processor board ID JAD042701EE (1286926306)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
4 Voice FXO interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
gateway#
============================================================

 

[kam72]

I have installed the IOS image. Can you please check my config. I am not able to registered with call manager.
===========================================================
lexia#
lexia#sh config
Using 1110 out of 29688 bytes
!
version 12.2
service config
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname lexia
!
enable secret 5 $1$DKz5$F5gB9Eny2PwXiwZsjpT/b/
enable password voip
!
ip subnet-zero
!
mgcp
mgcp call-agent 192.168.0.111
mgcp dtmf-relay codec all mode out-of-band
call rsvp-sync
!
ccm-manager mgcp
!
interface FastEthernet0/0
ip address 192.168.0.55 255.255.255.0
no ip mroute-cache
speed auto
full-duplex
no cdp enable
!
interface Serial0/0
no ip address
no ip mroute-cache
shutdown
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.0.111
no ip http server
!
snmp-server community public RO
snmp-server enable traps tty
!
voice-port 1/0/0
!
voice-port 1/0/1
!
voice-port 1/1/0
!
voice-port 1/1/1
!
dial-peer cor custom
!
dial-peer voice 1 pots
application mgcpapp
port 1/0/0
!
dial-peer voice 2 pots
application mgcpapp
port 1/0/1
!
dial-peer voice 3 pots
application mgcpapp
port 1/1/0
!
dial-peer voice 4 pots
application mgcpapp
port 1/1/1
!
line con 0
exec-timeout 0 0
line aux 0
line vty 0 4
password voip
login
!
end

lexia#
%Error opening tftp://255.255.255.255/network-confg (Timed out)
04:00:27: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/network-confg) failed
%Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
04:00:51: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/cisconet.cfg) failed
lexia#
lexia#
%Error opening tftp://255.255.255.255/lexia-confg (Timed out)
04:01:15: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/lexia-confg) failed
===========================================================
Could you please let me know why i am getting the above errors.

Thanks

 

[pndscm]

Here's one of my config's:
!
ip cef
!
voice-card 0
!
ccm-manager fallback-mgcp
ccm-manager redundant-host 10.10.10.10
ccm-manager mgcp
ccm-manager music-on-hold
ccm-manager config server 10.10.10.10
ccm-manager config
!
logging trap debugging
!
control-plane
!
call application alternate default
!
voice-port 0/0/0
!
voice-port 0/0/1
!
voice-port 0/0/2
!
voice-port 0/0/3
!
mgcp
mgcp call-agent 10.10.10.11 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp package-capability rtp-package
no mgcp package-capability res-package
mgcp package-capability sst-package
no mgcp package-capability fxr-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
!
mgcp profile default
!
dial-peer voice 999000 pots
application mgcpapp
port 0/0/0
!
dial-peer voice 999001 pots
application mgcpapp
port 0/0/1

You probably don't need all the mgcp or ccm-manager commands.
The errors you are getting look like the router is trying to boot from the network. Type in 'no service config'.

 

[kam72]

Great I have followed your instructions after typing no service config i am not getting errors.

Can you please give me the config file based open the following details.
============================================================
1. My Call manager ip address is 192.168.0.111
2. Router ip address is 192.168.0.55
3. I am confused here "mgcp call-agent 10.10.10.11 2427 service-type mgcp version 0.1" In my case what ip address shall i use?

Please also see my sh version
============================================================
lexia#sh version
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-JS-M), Version 12.2(31), RELEASE SOFTWARE (fc2)
Technical Support:

http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 11-Aug-05 17:24 by tinhuang
Image text-base: 0x8000808C, data-base: 0x814710D8
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-JS-M), Version 12.2(31), RELEASE SOFTWARE (fc2)
lexia uptime is 8 minutes
System returned to ROM by reload
System image file is "flash:c2600-js-mz.122-31.bin"
cisco 2620 (MPC860) processor (revision 0x102) with 61440K/4096K bytes of memory
Processor board ID JAD042701EE (1286926306)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
4 Voice FXO interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
lexia#
============================================================
Thanks for your reply

 

[kam72]

Cisco 2620 is successfully registered with CCM please see attached.

So what should i do to make a call from the 7940 ip phone which is registered to the CCM.

Even I have followed the instruction

http://www.cisco.com/en/US/products...ducts_tech_note09186a008017825e.shtml#task14x

but unable to make a call.

Is there any particular reason?

Thanks

 

[kam72]

Configured GW and also registered in CCM But the problem is 1. I cannot make a call from IP Phones.
2. If i call bell is ringing on IP Phone but cannot hear
both sides.

I can ping IP phone from GW. Any Suggestion how to rectify problem

Thanks