Programing a T1

[FireFighter78]

Hi Guys,

I am building an Option 11 release 21.35 (to replace an Option 21 that is dying of a slow and painful death) I guess I should say that I am remodeling an Option 11 seeing that it is used.

So they had it setup with some multi site setup, ACD stuff, etc. The trunk stuff is kicking my butt big time. They were using NARS/BARS and other stuff that I understand conceptually. I really need some help finding the stuff I need to OUT and then putting it back in for our fairly simple T1-PRI (one location, everything in and out the same telco T1).

My level of understanding is medium, I think???? I don’t really need some one to do it for me (although that would be nice) but I could use a hand to hold onto when the road gets rough (the outbound path is quite rutty).

Thanks!!!!

 

[telebub]

I'm not sure how detailed you want to get but here is a start...

1) If applicable, disable the d-channel in LD 96
2) Disable the Loop in LD 60
3) Out the trunks in LD 14
4) Out the Route in Ld 16
5) Out the d-channel in LD 17 under gate opener ADAN
6) Out the loop in LD 17 under gate opener CEQU
7) Rebuild the loop in LD 17 under gate opener CEQU
8) If applicable, build the d-channel in LD 17 under ADAN
9) Build the route in LD 16
10) Build the trunks in LD 14

Things to be aware of and look at:
1) NET data in customer data block. Print in LD 21
2) Clock Controller data. Prt DDB in LD 73. Enable and disable in LD 60.
3) BARS/NARS LDs 86, 87, and 90

Hope this helps.

War Eagle!
Lions Baseball '09!

 

[johnpoole]

ld 60 stat, will show you t1's that are built.. ld 21 ltm will show you all your trunk members.. IF you do not want restrictions you can make the acod of your t1 9.. then just use nfrl (ld 49) to build an allow table.. you would not need ld 90, 87 or 86..

ld 22 prt cequ, will show the hardware map of that OLD box..

IF you have the original install and keycodes you can wipe out everthing and start new.. it takes about two full days to program one from scratch.. if you do that, you will know whats built and how it's put together..

you can have dial 9 and dial 8 with restrictions without bars/nars But. bars it way quicker if you need to allow and deny certain types of calls

john poole
bellsouth business
columbia,sc

 

[FireFighter78]

At the end is my RDB and TRK

@JohnPoole the old system will not let me talk to it at all.

Does it look like I have done it correctly?

Thanks!!

This is the info from the TELCO –

>Product Digital Trunks (VT1)
>BTN 585-582-1230
>In start dial Wink
>Out start dial Wink
>Pulsing DTMF
>Sw supv EM2
>Digits sent 4
>Clr ID ELIM BIBLE

TYPE RDB
CUST 00
DMOD
ROUT 0
TKTP DID
SAT NO
RCLS EXT
DTRK YES
DGTP DTI
ISDN NO
PTYP DCO
AUTO NO
DNIS NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 9
CPP NO
TARG
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
TFD 0
SST 5 0
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR YES
INC YES
LAST NO
TTA NO
QREC NO
OAL NO
OTL YES
AIA YES
OAN YES
OPD NO
NATL YES
MUS NO
MR NO


PAGE 002

RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TTBL 0
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0



TN 004 01
TYPE DID
CDEN SD
CUST 0
NCOS 0
RTMB 0 1
A/B BIT SIGNALING
NITE 8199
SIGL LDR
STRI/STRO WNK WNK
SUPN NO
CLS UNR DTN WTA LPR APN THFD HKD
P10 NTC
TKID
DATE 28 APR 2009

TN 004 24
TYPE DID
CDEN SD
CUST 0
NCOS 0
RTMB 0 24
A/B BIT SIGNALING
NITE 8199
SIGL LDR
STRI/STRO WNK WNK
SUPN NO
CLS UNR DTN WTA LPR APN THFD HKD
P10 NTC
TKID
DATE 28 APR 2009

 

[phonz1]

chg sigl to e and m type trunks..

 

[johnpoole]

it will work built like that.. non pri.. just be sure the provider knows you want e/m ldr

john poole
bellsouth business
columbia,sc

 

[FireFighter78]

What is "e/m ldr"?

Point of interest - I spent yesterday and today programing the phones that we will need running when we cut over. We did good only a half dozen logic errors out of 130+ phones programed.

 

[FireFighter78]

I tested it this morning with e and m type trunks and it did not work.

what questions do I ask the telco to find out what variety T-1 we have? When I started on this project a while back I told our rep that I am T-1 challenged and I posted every thing they sent me.

 

[phonz1]

post a LD60 of the loop. WHat else is going on? ALso post a LD73, ddb for us

 

[FireFighter78]

Unlike the telephone sets themselves I cannot test the T-1 as easily.

I connected the T-1 this morning and the “Red Alarm” did not clear. I could not ENCH the loop when I tested but I could ENCH 4 1.

Thanks again for your help!


>LD 60
DTI000
.STAT

PRI* TRK LOOP 4 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : RED
CH 01 - DSBL DID CH 02 - DSBL DID
CH 03 - DSBL DID CH 04 - DSBL DID
CH 05 - DSBL DID CH 06 - DSBL DID
CH 07 - DSBL DID CH 08 - DSBL DID
CH 09 - DSBL DID CH 10 - DSBL DID
CH 11 - DSBL DID CH 12 - DSBL DID
CH 13 - DSBL DID CH 14 - DSBL DID
CH 15 - DSBL DID CH 16 - DSBL DID
CH 17 - DSBL DID CH 18 - DSBL DID
CH 19 - DSBL DID CH 20 - DSBL DID
CH 21 - DSBL DID CH 22 - DSBL DID
CH 23 - DSBL DID CH 24 - DSBL DID


REQ PRT
TYPE DDB

CLKN 1
PREF FREE RUN
SREF FREE RUN

TRSH 07
RALM 3
BIPC 2
LFAC 3
BIPV 3 2
SRTK 5 30
SRNT 15 3
LFAL 17 511
SRIM 1
SRMM 2

 

[phonz1]

do you have a clock controller on the T-1 card? what is the T-1 card part number??

 

[FireFighter78]

Yes I have the NTAK20 clock controller on my NTAK09 card (and no I don't have the NTAK93 D-channel controller).

Also I have the dip switches set for 533 - 655 feet the same as the repeater that it connects to. DCH F/W is off.

 

[phonz1]

ok, you need to find a loopback plug and loop up your local end and post those results

 

[FireFighter78]

Loopback passed, I think. Results of stat while loopback plug was plugged in.

.STAT

PRI* TRK LOOP 4 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE DID CH 02 - IDLE DID
CH 03 - IDLE DID CH 04 - IDLE DID
CH 05 - IDLE DID CH 06 - IDLE DID
CH 07 - IDLE DID CH 08 - IDLE DID
CH 09 - IDLE DID CH 10 - IDLE DID
CH 11 - IDLE DID CH 12 - IDLE DID
CH 13 - IDLE DID CH 14 - IDLE DID
CH 15 - IDLE DID CH 16 - IDLE DID
CH 17 - IDLE DID CH 18 - IDLE DID
CH 19 - IDLE DID CH 20 - IDLE DID
CH 21 - IDLE DID CH 22 - IDLE DID
CH 23 - IDLE DID CH 24 - IDLE DID

 

[phonz1]

ok, so your problem is from that point of the loop back outward.... if you go into a smart jack, call your Telco...

But yes, your post is how a normal T-1 should look when it's up!

 

[FireFighter78]

This morning I connected the T-1 to the Opt 11. When I dialed 9 (telco is providing dial tone) I get an electronically distorted dial tone - for lack of better description.

We would really prefer to match the current T-1 rather than changing it.

 

[phonz1]

so, the T-1 is up and looks good on your end?? I'd call Telco, that end may need to be bounced!

 

[FireFighter78]

Bounced? When I reconnect it to the Option 21 it works fine.

Does "bounce" mean something like releasing and renewing an IP address?

 

[phonz1]

bounce is having both ends reset at the same time... Okay, so what's different between the 21 and the 11 in programming?

 

[FireFighter78]

That goes back to why we are changing systems, the 21 will not accept input from the terminal.

Here is link to my thread on that problem -

http://www.tek-tips.com/viewthread.cfm?qid=1529160&page=1

Although the 21 would have to go sooner or later since we are down to 1 set of working floppies.