Print and Out and Rebuild 2250 DN on 2616 phone

[SwitchWitch]

Hello All,
Here's my delimina.

I have a 2250 terminal, with ###-###-3500 ringing on it.
The department that uses -3500 are all setup under Tenant 12; whereas the rest of the company are under Tenant 1.

I want to out the 2250 terminal and setup 3500 on a regular 2616 phone (no add-on, no special features).

I figured I could place -3500 in the IDC table and point to -3511 (which is built on the 2616 phone), this works, but no one can dial -3500 internally.

So, I figure I have to out the 2250 terminal altogether, but before doing so, I wanted to print out how this terminal is currently configured (just in case the department wants it back @ a later date).

Another block I'm running into is that @ one time there were (8) 2250 consoles setup. Now all are disconnected, but never removed from the switch.

Any suggestions

 

[NortelGuy1979]

Can you print a DNB of 3500, and also your ATT_DATA and LDN_DATA?

Thanks,
Matthew

Matthew - Technical Support Engineer

http://www.linkedin.com/in/matty79

 

[SwitchWitch]

Thanks for reply Matthew,

In LD 20, here is 3500:
DN 3500
CPND
NAME A10
XPLN 5
DISPLAY_FMT FIRST,LAST
TYPE LDN

How do you print the ATT-DATA and the LDN_DATA?

 

[NortelGuy1979]

ATT_DATA and LDN_DATA are both in LD 21.

So 3500 is an LDN, you can remove it from the LDN_DATA in LD 15 and then program it as an SCR on any set you'd like.

>ld 21
PT1000

REQ: prt
TYPE: ldn
TYPE LDN_DATA
CUST 0

TYPE LDN_DATA
CUST 00
OPT XLDN
DLDN NO
LDN0 301
LDN1 302
LDN2
LDN3
LDN4
LDN5
ICI 00
ICI 01
ICI 02
ICI 03
ICI 04
ICI 05
ICI 06
ICI 07
ICI 08
ICI 09

REQ: end
>ld 15
CDB000
MEM AVAIL: (U/P): 98677512 USED U P: 5426222 166087 TOT: 104269821
DISK SPACE NEEDED: 235 KBYTES
REQ: chg
TYPE: ldn

TYPE LDN_DATA
CUST 0
OPT
DLDN
LDN0 301
LDN1 x
LDN2
ICI

MEM AVAIL: (U/P): 98677515 USED U P: 5426222 166084 TOT: 104269821
DISK SPACE NEEDED: 235 KBYTES
REQ: end


>ld 21
PT1000

REQ: prt
TYPE: ldn
TYPE LDN_DATA
CUST 0

TYPE LDN_DATA
CUST 00
OPT XLDN
DLDN NO
LDN0 301
LDN1
LDN2
LDN3
LDN4
LDN5
ICI 00
ICI 01
ICI 02
ICI 03
ICI 04
ICI 05
ICI 06
ICI 07
ICI 08
ICI 09

-Matthew

Matthew - Technical Support Engineer

http://www.linkedin.com/in/matty79

 

[msteeler]

You prt the ATT and LDN data in LD 21. You make the changes in LD 15.