My first question is how are the systems connected exactly?
I do have a Point to Point programming and seamless dialing plan sheet.
Is that what you're looking for??
Seamless dialing plan
Site A:
2XX extensions
Dest code 5 ANY / absorb length: None
Points to Route 001 / Using pool with point to point channels
Each phone to be assigned a target line with their extension number as the received digits.
Build remote package 01 to have pool access to PTP pool set to yes.
Assign remote package 01 to the PTP channels
Dest code 9 / absorb length: 1
Points to Route 002 / Using pool with outgoing PSTN lines.
Site B:
5XX extensions
Dest code 2 ANY / absorb length: None
Points to Route 001 / Using pool with point to point channels
Each phone to be assigned a target line with their extension number as the received digits.
Build remote package 01 to have pool access to PTP pool set to yes.
Assign remote package 01 to the PTP channels
Dest code 9 ANY / absorb length: 1
Points to Route 002 / Using pool with outgoing PSTN lines.
Point to Point T-1 programming
If you are using a T-1 you will need to tell Telco which channels you want to designate E&M tie circuits.
To Disable / Enable Card
From Terminals & Sets – Next until you get to
Maintenance – Show
Next until get to Module Status – Show
Show module – Next
KSU (1): Next or State if using (2) cards
KSU (2): State
( ) Ports Busy – Press Disable or Enable
Disable at Once? – Yes
Protocols & Signaling
Hardware – Show
Show Module – Next
Cards on KSU – Show
Cd1 – KSU: Change to T-1 – Show
Card Type T-1 – Next
Lines: 001-024 – Next
Protocol: SL1 – Next (check with your Telco Carrier for setting)
Type Slave – Next
Bchanseq: Ascend or Descend – Next (check with your Telco Carrier for setting)
CO Fail: TIA–547A – Next
IF Levels: ISDN – Next
Framing: ESF – Next (usually ESF, check with your Carrier
Internal CSU: ON – Next
DSX1 Bld: 000-100
Line Coding: B8ZS (usually B8ZS, check with the Carrier)
ClockSrc: Primary (second card would be secondary)
Re-enable the card in Maintenance now.
In order for site A to dial site B you will need to put all the E&M channels in a line pool, assign it an access code and give that line pool access to each extension.
Line programming:
Lines – Show
Show Line:
Line001:Line001 – Show
Trunk / Line Data – Show
Trunk Type: E&M
Line Type: Pool C or any other unused pool
Dial mode: Tone
PrimeSet: 221
AutoPrivacy: N
Ans Mode: Auto
Aux Ringer: N
Signal: Wink
Ani number: N
DNIS number:N
Gain: Normal
Assigning Line Pool Access:
Terminals & Sets
Show set: (enter ext#) – Show
Line Access – Show
Line Assignment – Next
LinePool Access – Show
LinePoolA: Y – NEXT
LinePoolC: N – Change to Yes
This must be done each extension you want to be able to dial to the other site.
When callers from one side pick up their handset and dial the access code for the line pool containing the E&M channels they will hear intercom tone of the other side. They can then dial an extension. In order for the call to ring at the dialed extension you must assign a Target Line to each extension of both sides. The Received digits will be the extension number itself.
Target Lines Programming:
From Lines – Show
Show LN: 145 – Show (target line numbering differs depending on your software
1.0 sw – Lines number 121-312
R1T1 – Lines number 121-248
1.1 – Lines number 121-248 or 312 XC sw
2.0 to 5.0 – Lines number 145-272 or 336 XC sw
6.0 – Lines number 157-284 or 348 XC sw
Target LN – Next
Private to: (extension number) – Next
Rec’d #: (enter extension #) – Next
If Busy: to prime – Next
PrimeSet: 221 change to the extension # - Next
CLID Set: None – Next
Aux. Ringer: N – Next
End of list
MRoberts
