Optipoint station in UNACH condition - how to reset

[ccmjgb]

Greetings,

How can a digital port with UNACH status be re-enabled or reset?

The following has been attempted with no success:

RES-DSSUEN,1-X-Y-Z;
DEA-DSSU,
ACT-DSSU

Thank you!

ccmjgb
- Psalm 144:3

 

[sbcsu]

RES-DSSU:STNO or PEN
normally works
If still UNACH then the pair is not reaching the phone

 

[ccmjgb]

10-4, thank you!

 

[donb01]

Doesn't UNACH mean UNAssigned CHannel?? Meaning the port is not in use? I'm used to seeing RBLK if the system can't find the phone, or DEF/DEFIL if the system can't find the phone for long enough or something is wrong with it.

DEF/DEFIL can usually be fixed with DEA-DSSU and ACT-DSSU. I've never used RES-DSSU yet, but I'll have to check it out.

 

[sbcsu]

Extract here:

H02: MODULE <pen> ACTIVATED
(Module activated and operational.)
H03: MODULE <pen> ACTIVATED - NOT OPERATIONAL (NEQ)
(Module is not operational, since it is ’not equipped’.)
H04: MODULE <pen> ACTIVATED - NOT OPERATIONAL (DEF)
(Module not operational, status = ’defective’.)
H05: MODULE <pen> ACTIVATED - NOT OPERATIONAL (NPR)
(Module not operational, state = ’not present’.)
H06: MODULE <pen> ACTIVATED - NOT OPERATIONAL (UNACA)
(Module not operational, status = ’blocked due to interrelationship’.)
H07: MODULE <pen> ACTIVATED - NOT OPERATIONAL (UNACH)
(Module not operational, status = ’hierarchically blocked’.)
H08: MODULE <pen> ACTIVATED - NOT OPERATIONAL (UNACA-DEF)
(Module not operational, status = ’blocked due to interrelationship’ and ’defective’.)
H09: MODULE <pen> ACTIVATED - NOT OPERATIONAL (UNACA-NPR)
(Module not operational, status = ’blocked due to interrelationship’ and ’not present’.)
H10: MODULE <pen> ACTIVATED - NOT OPERATIONAL (UNACA-UNACH)
(Module not operational, status = ’blocked due to interrelationship’ and ’hierarchically blocked’.)
H11: MODULE <pen> ACTIVATED - NOT OPERATIONAL (UNACH-DEF)
(Module not operational, status = ’hierarchically blocked’ and ’defective’.)
H12: MODULE <pen> ACTIVATED - NOT OPERATIONAL (UNACH-NPR)
(Module not operational, status = ’hierarchically blocked’ and ’not present’.)
H13: MODULE <pen> ACTIVATED - NOT OPERATIONAL (UNACA-UNACH-DEF)
(Module not operational, status = ’blocked due to interrelationship’,’hierarchically blocked’ and
’defective’.)
H14: MODULE <pen> ACTIVATED - NOT OPERATIONAL (UNACA-UNACH-NPR)
(Module not operational, status = ’blocked due to interrelationship’, ’hierarchically blocked’ and ’not
present’.)
H15: MODULE <pen> ACTIVATED - NOT OPERATIONAL (WBT)
(Module not operational, status = ’wrong board type’)
H16: MODULE <pen> ACTIVATED - NOT OPERATIONAL (WBT-UNACA)
(Module not operational, status = ’wrong board type’ and ’blocked due to interrelationship’.)
H17: MODULE <pen> ACTIVATED - NOT OPERATIONAL (WBT-UNACH)
(Module not operational, status = ’Wrong board type’ and ’hierarchically blocked’.)
H18: MODULE <pen> ACTIVATED - NOT OPERATIONAL (WBT-UNACA-UNACH)
(Module not operational, status = ’wrong board type’, blocked due to interrelationship’ and ’hierarchically blocked’.)
H19: MODULE <pen> ACTIVATED - NOT OPERATIONAL (DEF-LOADERROR: n)
(Module not operational, status = defective, load error has occurred. ’n’ denotes the type of error.)
H20: MODULE <pen> ACTIVATED - NOT OPERATIONAL (UNACA-DEF-LOADERROR:n)
(In addition to error pattern H19 shown, the module is further ’blocked due to interrelationship’.)
H21: MODULE <pen> ACTIVATED - NOT OPERATIONAL (UNACH-DEF-LOADERROR:n)
(In addition to error pattern H19 shown, the module is further ’hierarchically blocked’.)
H22: MODULE <pen> ACTIVATED - NOT OPERATIONAL (UA/UH-DEF-LOADERROR:n)
(In addition to error pattern H19 shown, the module is further ’blocked due to interrelationship’ and
’hierarchically blocked’.)
H23: MODULE <pen> DEACTIVATED
(Module has been manually blocked)
H24: MODULE <pen> PRE-BLOCKED
(Module has been pre-blocked and is still operational.)

 

[luvarne]

res-dssu should to the trick. but use the PEN.