New PRI/DCH

[camaro67]

Hello all,
once again i need your help! i have a new PRI coming in a few days and i wanted to check my configuration before it got here I have an OPT11C RLS 4.0 i'm using a TMDI card(no clock) and a adtran CSU with a loop back jack installed on the network side. when i try to bring up the PRI all the channels go int MBSY.Is this normal since i dont have a Dchannel from the carrier?

PRI* TRK LOOP 5 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - MBSY DID VCE * CH 02 - MBSY DID VCE *
CH 03 - MBSY DID VCE * CH 04 - MBSY DID VCE *
CH 05 - MBSY DID VCE * CH 06 - MBSY DID VCE *
CH 07 - MBSY DID VCE * CH 08 - MBSY DID VCE *
CH 09 - MBSY DID VCE * CH 10 - MBSY DID VCE *
CH 11 - MBSY DID VCE * CH 12 - MBSY DID VCE *
CH 13 - MBSY DID VCE * CH 14 - MBSY DID VCE *
CH 15 - MBSY DID VCE * CH 16 - MBSY DID VCE *
CH 17 - MBSY DID VCE * CH 18 - MBSY DID VCE *
CH 19 - MBSY DID VCE * CH 20 - MBSY DID VCE *
CH 21 - MBSY DID VCE * CH 22 - MBSY DID VCE *
CH 23 - MBSY DID VCE * CH 24 - DCH 5
.****
OVL000
>ld 48
LNK000
.stat tmdi 5
TMDI 5: ENBL
DITI 5 OPER PORT 0
DCH 5 OPER PORT 1
.
.*
.*
.*
OVL000
>ld 96
DCH000
.stat dch 5
DCH 005 : OPER AEST AUTO
DES : WINDSTREAMPRI
.

 

[NortelGuy1979]

If you enable the DCH you should get a DCH RELEASE WRONG MODE - something to that effect; and then you know your hardware is good.

You won't get the channels to come up, no.

Matthew - Technical Support Engineer Sr.

http://www.linkedin.com/in/matty79

 

[camaro67]

No i dont get that message this is the message i get
DCH2040 {DCH #} {D-channel data}
PRI reported that primary D-channel is out-of-service.

Severity: Info

could the d-channel be programmed wrong?

here is what i have....
ADAN DCH 5
CTYP TMDI
CARD 05
PORT 1
DES WINDSTREAMPRI
USR PRI
DCHL 5
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP NDS
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO

 

[NortelGuy1979]

LD 60
DISL 5
LD 96
DIS DCH 5
DIS TMDI 5
<wait>
ENL TMDI 5 FDL
<wait>
ENL DCH 5
ENL AUTO 5
LD 60
ENLL 5

See what you get then?

Matthew - Technical Support Engineer Sr.

http://www.linkedin.com/in/matty79

 

[camaro67]

I had to disable the TMDI and do the FDL in ld 48 here is what i got for the rest of the commands...

DCH000
.enl dch 5
.enl auto 5
.
DCH: 5 RLS RED ALRM TIME: 14:09:48 8/07/2011
****
OVL000
>ld 60
DTI000
.stat 5

PRI* TRK LOOP 5 - DSBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
.enll 5

DTA003 5

PRI000 5 5

PRI000 5 5

PRI000 5 5

DTA023 5

OK
.
DCH2040 5 3
stat 5

PRI* TRK LOOP 5 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - MBSY DID VCE * CH 02 - MBSY DID VCE *
CH 03 - MBSY DID VCE * CH 04 - MBSY DID VCE *
CH 05 - MBSY DID VCE * CH 06 - MBSY DID VCE *
CH 07 - MBSY DID VCE * CH 08 - MBSY DID VCE *
CH 09 - MBSY DID VCE * CH 10 - MBSY DID VCE *
CH 11 - MBSY DID VCE * CH 12 - MBSY DID VCE *
CH 13 - MBSY DID VCE * CH 14 - MBSY DID VCE *
CH 15 - MBSY DID VCE * CH 16 - MBSY DID VCE *
CH 17 - MBSY DID VCE * CH 18 - MBSY DID VCE *
CH 19 - MBSY DID VCE * CH 20 - MBSY DID VCE *
CH 21 - MBSY DID VCE * CH 22 - MBSY DID VCE *
CH 23 - MBSY DID VCE * CH 24 - DCH 5

 

[NortelGuy1979]

Your loop came up in loopback, as expected (you got a DTA23 so thats good) - did you do an ENL DCH 5 or did I skip that part?

I'd expect a DCH054 RLS WRONG MODE ...

Matthew - Technical Support Engineer Sr.

http://www.linkedin.com/in/matty79

 

[RickyPone]

I'm not for sure but I don't think you get release wrong mode with ni2. at least I didn't when I put some in about six months ago.

 

[camaro67]

i did do enl dch 5 here is what i got back
>ld 96
DCH000
.enl dch 5
.enl auto 5
.
DCH: 5 RLS RED ALRM TIME: 14:09:48 8/07/2011
****
OVL000
>ld 60
DTI000
.stat 5

PRI* TRK LOOP 5 - DSBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
.enll 5

i get an error saying the dch is out of service

>err dch2040

DCH2040 {DCH #} {D-channel data}
PRI reported that primary D-channel is out-of-service.

when i stat dch 5
>ld 96
DCH000
.stat dch 5
DCH 005 : OPER AEST AUTO
DES : WINDSTREAMPRI

 

[RickyPone]

When windstream turns the circuit up and you connect to it the d-channel will probably establish.

 

[camaro67]

Ok that's what i am hoping for thanks everyone for your help!