Need to add second Admin terminal to G3r. 3

[Snapper]

I don't want dial up or C-Lan access. I need to install a second admin terimal to another location 500 feet away via telephone cross connect. I have the terminal. What do I need to do? Please help.

Attitude is everthing.
-Snapper

 

[mikeydidit]

Snapper I have my second terminal setup through a data module. Thats the only way that I know to hook it up at that distance. I have mine set up at 9600 and it works great.

Mike Jones
LSUHSC

 

[Snapper]

I have a data module. If you would be so kind as to show me how I would set that up?

Attitude is everthing.
-Snapper

 

[mikeydidit]

This is how the data module that I have for this is setup Snapper.

Page 1
DATA MODULE

Data Extension: xxxxx Name: REMOTE SAT BCC: 2
Type: data-line COS: 0
Port: 01C0306 COR: 1
ITC: restricted TN: 1
Page 2

DATA MODULE

CAPABILITIES
KYBD Dialing? y Configuration? n
Busy Out? n
SPEEDS
Low? n 1200? n 4800? n 19200? n
300? n 2400? n 9600? y Autoadjust? n

OPTIONS
Permit Mismatch? n Dial Echoing? y
Disconnect Sequence: two-breaks Answer Text? y
Parity: even Connected Indication? y


Mike Jones
LSUHSC

 

[Snapper]

How would I wire it up? I have to go through telco cross connect?

Attitude is everthing.
-Snapper

 

[Snapper]

What kind of packet card does this port work out off?

Attitude is everthing.
-Snapper

 

[mikeydidit]

The board that mine is installed on is a TN 726B data line. This is cross connected to a 4 pair and RJ-45 jack. Then a cable to the data module. I hit control break on the terminal to dial the data extension. Then I get the login prompt.

Mike Jones
LSUHSC

 

[Snapper]

What is the pin-out on the jack?

Attitude is everthing.
-Snapper

 

[mikeydidit]

It looks like it is setup as a regular 4 wire digital pack, so try the first pair to the white/orange and the second pair to the white/green.

Mike Jones
LSUHSC

 

[Snapper]

I've got it set-up, but it doesn't work. I get a cursor but no promt.

Attitude is everthing.
-Snapper

 

[Snapper]

The power and data are flashing (cannot Communicate with PBX). I have it connected directly to the PBX data port. Now what?

Attitude is everthing.
-Snapper

 

[mikeydidit]

Give me chance to look through the terminal setting. Their may be something that has to be setup in there.

Mike Jones
LSUHSC

 

[lopes1211]

Snapper - what is the pbx make and model and what model data module are you using?

-CL

 

[Snapper]

g3r V11, 7400b plus

Attitude is everthing.
-Snapper

 

[lopes1211]

Typically on a G3R, you would connect a TN726 to a TN533. You would then build 8 system data modules with the ports from the TN726 as the "port" and the ports from the TN533 as the "pdata port". Put the 8 data mods in a hunt group and you now have something similar to the Netcon group in a G3i.

change data-module 51801 Page 1 of 1 SPE B
DATA MODULE

Data Extension: 51801 Name: :SYSTEM PORT 01 BCC: 2
Type: system-port COS: 5
Port: 04B1101 COR: 27
ITC: restricted TN: 1
PDATA Port: 04B1201


Now flag the "data mod" field on your station to "yes" assuming your phone is on a 4-wire port since you're using a 4 wire data mod.

display station 6181 Page 6 of 6 SPE B
STATION

DATA MODULE

Data Extension: 4407 Name: 7400B Plus BCC: 2
COS: 1
COR: 1
ITC: restricted TN: 1

ABBREVIATED DIALING
List1:

SPECIAL DIALING OPTION:

Connect the data mod up to your terminal, and type atdt 1234 where 1234 is the netcon hunt group number. You can now have up to 8 terminal anywhere you have a digital phone. It's a lot more dynamic and you don't need any special rewiring to move it around. It's just working on a standard DCP port.


-CL

 

[mikeydidit]

After pulling up the dialin number, my dialin numbers are set in a hunt group. I am not sure about the Tn533 as this was setup 11 years ago.

Mike Jones
LSUHSC

 

[Snapper]

I have the hunt group in place and I've set up my station with data module. Where do I plug in the terminal and data module?

Attitude is everthing.
-Snapper

 

[Snapper]

What type of station set should I use?

Attitude is everthing.
-Snapper

 

[mikeydidit]

These are wired off your data line pack, and thats how mine are in the switch. These are assigned as members of the hunt. My data module plugs to the back of the terminal itself.

Mike Jones
LSUHSC

 

[Snapper]

I think we are making progress. After I did the atdt xxxx command I get a "No Carrier", now what?

Attitude is everthing.
-Snapper