MISP AND SILC CARD CONFIGURATION

[mceran1]

Dear Friend,
We have Nortel Meridian 1 Option 11C, Release 25.40B. We have ISDN PRI connections. The lines and D-Channel already working. We are trying to connect STE telephones (release 2.4 - euroISDN) using MISP and SILC card. All configurations are made already but STE is not giving any dial tone. When I check SILC cards DSL port status is
SW DSL L2 #TEI L1
00 IDLE LINE ESTA 1 UP
I can give you more detail if you interested in.
Is there anybody who can help me about this subject.

I thank you very much for your help .

 

[mikeyb123]

wired up correctly?

It's not getting any smarter out there. You have to come to terms with stupidity, and make it work for you.

 

[mceran1]

Hi mikeyb123,
I thank you very much for your answer. It's wired up correctly.
this is my stuation..
we have
Nortel Meridian 1 Option 11C release 25.40B
NTBK50AA PRI CARD
NTBK22AA MISP CARD
NT6D70AA SILC CARD

SETUP FOR BRI EXTENSIONS IN LD 27:
LAPD conf.
REQ PRT
TYPE LAPD
PGPN 9
USER
PGPN 9
LAPD
T200 4
T203 20
N200 8
N201 260
K 1
N2X4 10
#DSL 4
#ROUTES 0

MISP conf
REQ NEW
TYPE MISP
LOOP 36
APPL BRIL
APPL
DPSD NO


DSL conf
REQ PRT
TYPE DSL
DSL 7 0
DATE
PAGE
DES
NACT
TN 7 0 0 0
DES BRI1
CUST 0
CTYPE SILC
OPT BRIL
MISP 36
MODE NTAS
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 9
PRID 2
PDCA 2
FDN
EFD
HUNT
EHT
TGAR 1
NCOS 0
SGRP 0
CAC_MFC 0
CLS UNR ICDD CDMD MRD UDI ABDD PGND
DATE 19 JAN 2005

TSP conf
REQ PRT
TYPE TSP
DSL 7 0
OPT
USID 2
MPHC NO
SPID 600301
600401
DN 6247 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS YES
FEAT HDT FND SFD CFTD MWD FBD HBTD CFXD DNO3 DNDY
SSRV_NI
DN 6248 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
CLOP NO
TRANS YES
FEAT HTD FND SFD CFTD MWD FBD HBTD CFXD DNO3 DNDY
SSRV_NI
DFDN 6247


SILC CARD STATU IN LD 32
>LD 32
. STAT 7
00 = IDLE LINE ESTA 1 UP
01 = IDLE LINE RLS 0 DOWN
02 = IDLE LINE RLS 0 DOWN
04 = IDLE LINE RLS 0 DOWN

a. One STE telephone already connected. When we off hook STE telephone :
the connected line to DSL (SILC Card) PORT 0 is as above status.
b. when we select None Secure Voice the STE gives "NETWORK REJECTED CALL" message
c. as I mentioned earlier we have no dial tone.
thanks

 

[cmawbey]

check against my setup


TN 4 0 1 1
DES ISDN2
CUST 0
CTYP SILC
OPT BRIL
MISP 0
MODE NTAS
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 2
PDCA 1
FDN
EFD
HUNT
EHT
TGAR 1
NCOS 0
SCPW
SGRP 0
CLS CTD ICDD CDMD MRD UDI ABDD

Colin

 

[cmawbey]

some more info.


You need software packages 203 216 235

You need a MISP and at least 1 SILC at each end

SILC has 8 4-wire ports numbered 0-7
Sockets used are RJ45 type
Even port connected to pins 5 and 4
Odd port connected to pins 3 and 6
Ports are polarity aware

SETUP FOR BRI EXTENSIONS:

All programming done in LD 27. Configuration has four parts.

Part 1 LAPD (Link Access Protocol Datablock)

REQ new
TYPE lapd
PGPN x (try 0)

LAPD yes
T200 2
T203 20
N200 3
N201 260
K 1
N2X4 10

PGPN <cr>

Part 2 MISP installation

For Option 11 MISP needs to be in slots 1-3 of main cab
For big switch MISP goes in a free slot of a network shelf. The card uses the EVEN loop of that slot. The odd
loop can not be used for any purpose.

REQ new

TYPE misp

LOOP x
(card number if Option 11 or the even loop from the slot in the network shelf of a big switch)

APPL bril (BRI line)
<cr> .....

MISP is brought up in LD 32:
ENLC x FDL for OP11
ENLL x FDL for big switch
(FDL is needed the first time to download the application 'bril')



Part 3 DSL (Digital Subscriber Loop)
This is configured 1 per BRI extension.

REQ new
TYPE dsl
TN c u or l s c u
DES BRI
CUST 0
CTYP SILC (UILC not used in the UK)
OPT BRIL
MISP x (Loop set up in part 2)
MODE NTAS



LAPD 0 (as set up in part 1)

PRID y (protocol ID)
This is dependant on terminal equipment but 'y' can be:
1=ANSI
2=ETSI (used here)
3=DMS
4=NET64
5=NUMERIS
6=NI-1



TGAR 0



CLS unr

<cr>

Part 4 TSP (Terminal Service Profile)
This is configured 1 per BRI extn.

REQ new

TYPE tsp

DSL c u or l s c u (of the DSL set up in part 3)

USID 0 (used here) or
SPID aaaa..aa (Service profile ID, I think used in US)


DN xxxx

CT vce dta

DFDN xxxx (as above)


You should now have a working BRI line.

Colin