Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

MICS Upgrade Question

Status
Not open for further replies.
rval80

rval80

Technical User
Sep 23, 2009
386
US
It's been quite a while since I've upgraded a MICS, so my question is this; I have a customer that currently has a DR6.0 release mics and wants to upgrade the software. I have a DR7.0 that I pulled off a system a while back that I upgraded to XC7. Do I need the upgrade tool for DR6 to DR7, and should there be any issues with me using software that I pulled out from a different system (ie programming)? Thanks!
 
Sort by date Sort by votes
So, going from 6.0 to 7.0 won't work? I need the 6.1 in between?

Thanks again!
 
Upvote 0 Downvote
Thanks curlycord. Should I use the upgrade tool from 6 to 7?
 
Upvote 0 Downvote
So I'm thinking now that I may just upgrade them from the 6.0 to the 6.1 and use their existing NVRAM cartridge. Therefore, I can back up the programming and if something gets lost, I can restore without an issue. Any thoughts?
 
Upvote 0 Downvote
Wouldn't I be able to restore to the 6.1? I'm not changing the NVRAM cartridge, and if I'm not mistaken, that's where the programming is held. I'm hoping it doesn't come down to this, as I'm assuming the upgrade should go alright.
 
Upvote 0 Downvote
You cannot back up one software and restore to another software.
NVRAM should be Rls 2 btw
Programming is on the KSU.

Did you read the Upgrade procedure yet in the Install Guide?.






=----(((((((((()----=
curlycord
 
Upvote 0 Downvote
Curlycord, I read the manual and it's saying that going from 6.0 to 6.1 only requires new software card. It sounds like it's safe for me to use the existing NVRAM that is in place.
 
Upvote 0 Downvote
Curlycord and Exsmogger, thank you for all of your advice. You have both been great.
 
Upvote 0 Downvote
Ok, I upgraded from a 6.0 to 6.1 today and everything went fairly smooth. Customer just called and said the phones that have the busy lamp field modules on them are having issues. It appears as though the BLF mod's are blinking. They disconnect them and reconnect them and they work for about 15 minutes and start blinking again. These are compatible with the 6.1 aren't they?
 
Upvote 0 Downvote
They should be compatible. What is your version of 6.1? I forgot to mention that the MR (maintenance release) version of 6.1 fixed all the bugs in the earlier versions of 6.1. In Maintenance the system version should display as 30CQG05 or 30CQG10 if it's the MR version of 6.1.

Brian Cox
Oregon Phone
 
Upvote 0 Downvote
In order for BLF to work on 6.1 the the phone must Rls 16 or greater.
Hopefully not too many have BLF's, in this case look under all sets and start swapping Rls 16's for those with BLF.



=----(((((((((()----=
curlycord
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

Don W
  • Locked
  • Question
Mics software upgrade tools
Replies
9
Views
769
curlycord
curlycord
P
  • Locked
  • Question
Incoming calls go to dial tone on Nortel MICS-XC 7.0
Replies
11
Views
1K
curlycord
curlycord
dmcdream
  • Locked
  • Question
Compact ICS Flash ROM Card - software upgrade
Replies
4
Views
830
Firebird Scrambler
Firebird Scrambler
jsaad
  • Locked
  • Question
MICS GATC going dead 4
2
Replies
24
Views
1K
curlycord
curlycord
Michael OConnor
  • Locked
  • Question
Norstar MICS Extension Call Forward External 4
Replies
12
Views
906
ttEstiNg2023
ttEstiNg2023

Part and Inventory Search

Sponsor

Back
Top