hi! I have 3070 sopho system,DLX-L board, PNT-L network terminator and some ISDN modems (USB and PCI modems,ETSI-ISDN),RVS software (ISDN applications, telephony/ fax/ videotelephony/ file transfers etc).I try to follow step by step data facilities but desn't work,the ISDN loop test failed.I want to use all applications of RVS and both B channel( I don't understand how assign to one circuit 2 MSN/BSP-ID?)What are the correct settings for this purpose (fcm/ibsc/bspt/cv..etc)?Excuse me for my poor english.
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
isdn modem/data circuits setting problems
- Thread starter narse
- Start date
I haven't done this for a long time but I just remembered something <g>. Just test your options in your own environment and see what it will do for you together with your application. I use the OM commands because I don't remember or have no clue where to find them in SysManager ......
Good luck !!
1. With CHDNRC you can add more numbers to a circuit and gives you the option to put it above or under the existing DNR. Note: FCM's and features of the 1st DNR can be used !!
2. 22031979 is right to change the BSPT/IBSC value.
DIDNRS:12345&12345;
CHDNRS:98,0,12345;
CHDNRS:98,0,12346;
(Check the format, it has been 3 years !!)
3. Check your S0 bus Hwa's;
Your ergoline's or other digital phones use fixed MSN with one digit. You can change the MSN type to 1 with the amount of digits you use in your internal number scheme.
Note: Was always nice when people want to reuse the Hwa's again for regular phone's, yup >> everybody forgot to put these settings back.
dimsnp:4061,1,30&31;
chmsnp:4061,1,30,1,5;
chmsnp:4061,1,31,1,5;
(Check the format again !!)
Maybe unnecessary but check if they are installed :
DISERV:4061,1,30&31;
SETINS:4061,1,30&31;
DISERV:4061,1,30&31; again
4. If I am correct the Fixed digits in your exchange will not have any effect anymore. Usully on the S0 bus they were 2&3 in your pbx and for the phones 2&3 (D622) or 0&1 (Ergoline). I used to leave them alone.
DIFMSN:12345&12346;
CHFMSN:12345,2;
CHFMSN:12346,3;
5. Last thing is that you can add channel bundling to your DNR's if necessay with ASFACM. I believe it was 56. Just check ASFACM:? for the complete list.
I hope this might help you.
Greetz
Sophoman
Time 4 some coffee ... Douwe Egberts of zo.
(Toch maar een Heineken)
Good luck !!
1. With CHDNRC you can add more numbers to a circuit and gives you the option to put it above or under the existing DNR. Note: FCM's and features of the 1st DNR can be used !!
2. 22031979 is right to change the BSPT/IBSC value.
DIDNRS:12345&12345;
CHDNRS:98,0,12345;
CHDNRS:98,0,12346;
(Check the format, it has been 3 years !!)
3. Check your S0 bus Hwa's;
Your ergoline's or other digital phones use fixed MSN with one digit. You can change the MSN type to 1 with the amount of digits you use in your internal number scheme.
Note: Was always nice when people want to reuse the Hwa's again for regular phone's, yup >> everybody forgot to put these settings back.
dimsnp:4061,1,30&31;
chmsnp:4061,1,30,1,5;
chmsnp:4061,1,31,1,5;
(Check the format again !!)
Maybe unnecessary but check if they are installed :
DISERV:4061,1,30&31;
SETINS:4061,1,30&31;
DISERV:4061,1,30&31; again
4. If I am correct the Fixed digits in your exchange will not have any effect anymore. Usully on the S0 bus they were 2&3 in your pbx and for the phones 2&3 (D622) or 0&1 (Ergoline). I used to leave them alone.
DIFMSN:12345&12346;
CHFMSN:12345,2;
CHFMSN:12346,3;
5. Last thing is that you can add channel bundling to your DNR's if necessay with ASFACM. I believe it was 56. Just check ASFACM:? for the complete list.
I hope this might help you.
Greetz
Sophoman
Time 4 some coffee ... Douwe Egberts of zo.
(Toch maar een Heineken)
- Status