IPO500V2 Red LIghts

[diegosaletti]

good afternoon guys.

I have a IPO500 v2 8.0.44, to perform a reset the LED turned red and not go out, I tried connecting via DTE and hyper terminal shows the following:

   
P14 Loader v1.32
CPU Board Version is: 0x04
CPU PLD Version is: 0x25
CPUID: 0x12 Present: Present2 0xA0: 0x02
Using FPGA build 0x00000827
Programming FPGA ...
FPGA Version 0x01 0x00 Build ID 0x00000827
Initialising NAND device .. registering ..
Added device: Samsung 64MB NAND (small block) - 0x0001

SMXFS: This is a SD card 2.0
SMXFS: This is SDHC card
SMXFS: IT'S SD / SDHC CARD
SMXFS: Sector Number is 762000
SMXFS: Sector Size is 200
OPTIONAL SD Card not present / Recognised
Initialising FileSys device .. registering ..
Added FileSys device
Primary System is INVALID
System Backup is INVALID
NO Main Image file
Bootp Location:
A: \ system \ primary \ ip500v2.bin

P14 Loader v1.32 (128 MB SDRAM)
MPC8248 CPU Revision 0x0C10
Broadcom Switch Mode was 0x05 0x06 now
EthChipRevId: 0x01 EthPhyId: 0x0143BC30
Sending BOOTP Request
Power glitch fail ignored, high = 00000002
Power has failed!

I read in some places that ipo500 may have lost your OS.

could help me solve this?
sorry for my poor english.

Thanks

 

[tlpeter]

Try to recreate the SD card.

BAZINGA!

I'm not insane, my mother had me tested!

 

[diegosaletti]

Have recreated sdcard but without formatting, and it did not work.
I'll try to format the sdcard and rebuild again right now.

tks

 

[diegosaletti]

good afternoon.

I tried the procedure to format and rebuild the sdcard, but still the error occurs:

SMXFS: This is a SD card 2.0
SMXFS: This is SDHC card
SMXFS: IT'S SD / SDHC CARD
SMXFS: Sector Number is 762000
SMXFS: Sector Size is 200
OPTIONAL SD Card not present / Recognised
Initialising FileSys device .. registering ..
Added FileSys device
Primary System is INVALID
System Backup is INVALID
NO Main Image file
Bootp Location:
A: \ system \ primary \ ip500v2.bin

P14 Loader v1.32 (128 MB SDRAM)
MPC8248 CPU Revision 0x0C10
Broadcom Switch Mode was 0x05 0x06 now
EthChipRevId: 0x01 EthPhyId: 0x0143BC30
Sending BOOTP Request

I am onsite at the client and do not know what else to do.

thanks!

 

[intrigrant]

Well, put the card in a card reader and locate the file ip500v2.bin on your PC harddrive, copy it to the SD card directory
\system\primary put the card in the ipo and try again.

A simple mind delivers great solutions

 

[diegosaletti]

@intrigrant

performed the procedure you asked, below is the information from hyper terminal:

FPGA Version 0x01 0x00 Build ID 0x00000827
Initialising NAND device .. registering ..
Added device: Samsung 64MB NAND (small block) - 0x0001

SMXFS: This is a SD card 2.0
SMXFS: This is SDHC card
SMXFS: IT'S SD / SDHC CARD
SMXFS: Sector Number is 762000
SMXFS: Sector Size is 200
OPTIONAL SD Card not present / Recognised
Initialising FileSys device .. registering ..
Added FileSys device
Primary System is INVALID
System Backup is INVALID
NO Main Image file
Bootp Location:
A: \ system \ primary \ ip500v2.bin

P14 Loader v1.32 (128 MB SDRAM)
MPC8248 CPU Revision 0x0C10
Broadcom Switch Mode was 0x05 0x06 now
EthChipRevId: 0x01 EthPhyId: 0x0143BCA0
Sending BOOTP Request

not yet worked ....

any other ideas?

thanks!

 

[amriddle01]

The card seems to be buggered, try a new one, if it works ...cool (the swap licences I required) if not then may be the chassis I have had to replace a chassis due to a similar fault before


Avaya Implementation Qualified Professional Specialist Technical Engineer (AIQPSTE)

 

[diegosaletti]

okay. I'll try a new sdcard. Back soon with the results.
thanks everybody!

 

[intrigrant]

It does a BootP request so if your Avaya Manager has BootP enabled AND the working directory for the BIN files is correct AND the unit is registered in the BootP area of the IP Office Manager then it would pick up the file from your PC and boot up.
If it then still fails you'll have a bad unit, if it starts then you have a bad SD card.

A simple mind delivers great solutions

 

[amriddle01]

Indeed, good point Intrigrant, I believe that's how I pinpointed a dodgy chassis in my example


Avaya Implementation Qualified Professional Specialist Technical Engineer (AIQPSTE)

 

[diegosaletti]

Good morning guys

Problem solved.

Just replace the files and ipo500.bin ipo500v2.bin after this change the IPO worked.

thanks for all.

 

[amriddle01]

Hmmmm, when you formatted and recreated that happened anyway, or were you fibbing ?


Avaya Implementation Qualified Professional Specialist Technical Engineer (AIQPSTE)

 

[diegosaletti]

even reformatting and recreating gave error. But I got the files. bin from another laptop, it can be!