Installing Polycom HDX 8000 HD Video conference via BRI

[Pbxpoweruser]

Has anyone configured a Polycom HDX 8000 using BRI on a Nortel system. Any help would be appreciated!

thx

 

[NortelGuy1979]

Do you already have the Nortel set up w/ the BRI lines? That's the most difficult part; the Polycom is pretty simple if I remember right (entering the line #'s, SPID's, etc).

~M~

Matthew - Technical Support Engineer

 

[Pbxpoweruser]

We put a BRI card in the system but the actual video conference will go through the PRI... Do I need to create a route of some sort to route the BRI to the PRI?

 

[Pbxpoweruser]

Here are some prints

REQ prt
TYPE dsl
DSL
DATE
PAGE
DES
NACT


TN 9 0 0 0
DES VIDEO
CUST 0
CTYP UILC
OPT BRIL
MISP 4
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 6
PDCA 1
FDN 5602
EFD 5602
HUNT 5602
EHT 5602
TGAR 1
NCOS 7
SGRP 0
CLS CTD ICDD CDMD MRD ABDD PGND BRTD
DATE 19 AUG 2009


TN 9 0 0 1
DES VIDEO
CUST 0
CTYP UILC
OPT BRIL
MISP 4
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 6
PDCA 1
FDN 5604
EFD 5604
HUNT 5604
EHT 5604
TGAR 1
NCOS 7
SGRP 0
CLS CTD ICDD CDMD MRD ABDD PGND BRTD
DATE 19 AUG 2009


TN 9 0 0 2
DES VIDEO
CUST 0
CTYP UILC
OPT BRIL
MISP 4
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 6
PDCA 1
FDN 5606
EFD 5606
HUNT 5606
EHT 5606
TGAR 1
NCOS 7
SGRP 0
CLS CTD ICDD CDMD MRD ABDD PGND BRTD
DATE 19 AUG 2009


TN 9 0 0 3
DES VIDEO
CUST 0
CTYP UILC
OPT BRIL
MISP 4
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 6
PDCA 1
FDN 5600
EFD 5600
HUNT 5600
EHT 5600
TGAR 1
NCOS 7
SGRP 0
CLS CTD ICDD CDMD MRD ABDD PGND BRTD
DATE 19 AUG 2009


REQ prt
TYPE misp
LOOP

LOOP 4
APPL BRIL
DPSD NO
CARD1 9 0 0
CARD2
CARD3
CARD4


REQ prt
TYPE tps
DSL 9 0 0 0
OPT


USID 1
MPHC NO
SPID XXXXXXXXXX - What should be here exactly?

DN 5600 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FNA SFD CFTA MWD FBD CFXD DNO3 DNDY
SSRV_NI

DN 5601 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FNA SFD CFTA MWD FBD CFXD DNO3 DNDY
SSRV_NI

DFDN 5600

REQ prt
TYPE tsp
DSL 9 0 0 1
OPT


USID 1
MPHC NO
SPID XXXXXXXXXX - What should be here exactly?

DN 5602 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FNA SFD CFTA MWD FBD CFXD DNO3 DNDY
SSRV_NI

DN 5603 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FNA SFD CFTA MWD FBD CFXD DNO3 DNDY
SSRV_NI

DFDN 5602

REQ prt
TYPE tsp
DSL 9 0 0 2
OPT


USID 1
MPHC NO
SPID XXXXXXXXXX - What should be here exactly?

DN 5604 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FNA SFD CFTA MWD FBD CFXD DNO3 DNDY
SSRV_NI

DN 5605 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FNA SFD CFTA MWD FBD CFXD DNO3 DNDY
SSRV_NI

DFDN 5604

REQ prt
TYPE tsp
DSL 9 0 0 3
OPT


USID 1
MPHC NO
SPID XXXXXXXXXX - What should be here exactly?

DN 5606 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FNA SFD CFTA MWD FBD CFXD DNO3 DNDY
SSRV_NI

DN 5607 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FNA SFD CFTA MWD FBD CFXD DNO3 DNDY
SSRV_NI

DFDN 5606




REQ prt
TYPE lapd
PGPN
USER

PGPN 0
LAPD
T200 2
T203 20
N200 3
N201 260
K 1
N2X4 10
#DSL 4
#ROUTES 0

 

[Pbxpoweruser]

Here is a stat in LD 32

MISP ( BRIL ) LOOP
00 DSBL 02 BUSY
MISP 4 ENBL ACTIVATED : 08/19/09 11:21
BRIL : ENBL

.STAT 4
MISP ( BRIL ) LOOP
00 DSBL 02 BUSY
MISP 4 ENBL ACTIVATED : 08/19/09 11:21
BRIL : ENBL

.STAT 9

SW DSL L2 #TEI L1 D-CHANNEL RCVY CLK MODE
==== ==== ==== ==== ==== ========= ==== ==== ====
00 = IDLE LINE ESTA 2 UP
01 = IDLE LINE ESTA 2 UP
02 = IDLE LINE ESTA 2 UP
03 = IDLE LINE ESTA 2 UP
04 = UNEQ
05 = UNEQ
06 = UNEQ
07 = UNEQ
.

 

[NortelGuy1979]

The call will be placed using whatever BARS/NARS routing is in place for the particular number you are trying to call.

The call path is similar to this:

POLYCOM -> NORTEL BRI -> BARS/NARS -> PRI ROUTE (TELCO) -> BRI @ FAR-END PBX -> POLYCOM

So you must have PRI trunking in place, and ensure that whatever number you dial will route out that PRI route.

I believe (someone may correct me) that the route must be VOD.

~Matthew

Matthew - Technical Support Engineer

 

[Pbxpoweruser]

Ok so i am using PRI and the NARS BARS is functioning correctly. So the fact that is says 0 routes doesnt matter?

 

[NortelGuy1979]

a SPID is just a unique identifier for each line. Usually I would use something like 888-555-1212-0101 and -0102 where "888-555-1212" was the whole number.

What do you mean "0 routes" - where are you referring to?

Matthew - Technical Support Engineer

 

[dcross]

Your TSP should look like this.
REQ prt
TYPE tsp
DSL 68 0 4 0
OPT


USID 1
MPHC NO
SPID 92043322170101

DN 2217 0
CT DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
SSRV_NI

DFDN 2217


USID 2
MPHC NO
SPID 92043322180101

DN 2218 0
CT DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
SSRV_NI

DFDN 2218