Incorrect Digits across trunk

[DFM]

OK Folks,
Here is my problem. I have integrated Cisco to my G3r and am conducting tests. Here are the specifics

Extension 20000 (5 digit dial plan) has a UNI entry to AAR digits 234. Digits 234 steer calls to RP 400 with the only trunk group being Trk Grp 58 (below).

Here is a screen shot of the station trace I get when making a test call. Can someone figure out where I am going wrong? I want to pass 20000 to this Cisco gateway, but somewhere, I am inserting the leading digit of 4


12:40:14 tone-receiver 03E0206 cid 0x1940
12:40:14 active station 22096 cid 0x1940
12:40:16 dial 20000 route:UDP|AAR
12:40:16 term trunk-group 58 cid 0x1940
12:40:16 dial 20000 route:UDP|AAR
12:40:16 route-pattern 400 preference 1 cid 0x1940
12:40:16 seize trunk-group 58 member 24 cid 0x1940
12:40:16 Setup digits 40000
12:40:16 Calling Number & Name 6176622096 LCC-SOP
12:40:16 Proceed trunk-group 58 member 24 cid 0x1940
12:40:16 Alert trunk-group 58 member 24 cid 0x1940
12:40:18 active trunk-group 58 member 24 cid 0x1940
12:40:22 idle station 22096 cid 0x1940



Here are the associated switch translations…..



Group Number: 58 Group Type: isdn CDR Reports: y
Group Name: Definity to Call Manager COR: 62 TN: 1 TAC: 1458
Direction: two-way Outgoing Display? n Carrier Medium: PRI/BRI
Dial Access? n Busy Threshold: 5 Night Service:
Queue Length: 0
Service Type: tandem TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 0 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): enbloc/enbloc

Trunk Hunt: ascend
Digital Loss Group: 13
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0


TRUNK FEATURES
ACA Assignment? n Measured: both Wideband Support? n
Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: y Send Calling Number: y
Used for DCS? n Hop Dgt? n
Suppress # Outpulsing? n Numbering Format: public
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider

Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: y

Send UUI IE? y
Send UCID? n
Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation? n

US NI Delayed Calling Name Update? n

SBS? n Network (Japan) Needs Connect Before Disconnect? n




UNIFORM DIAL PLAN TABLE
Percent Full: 0

Matching Insert Node Matching Insert Node
Pattern Len Del Digits Net Conv Num Pattern Len Del Digits Net Conv Num
20000 5 1 234 aar n 4 5 1 enp n 2
24456 5 1 enp n 20 5 5 1 enp n 1
25 5 1 enp n 8 6 5 1 enp n 3


AAR DIGIT ANALYSIS TABLE
Percent Full: 71

Dialed Total Route Call Node ANI
String Min Max Pattern Type Num Reqd
234 7 7 400 aar n



Pattern Number: 400 Pattern Name: lcc > Call Mgr

Grp FRL NPA Pfx Hop Toll No. Inserted DCS/ IXC
No Mrk Lmt List Del Digits QSIG
Dgts Intw
1: 58 0 2 n user
2: n user
3: n user
4: n user
5: n user
6: n user

BCC VALUE TSC CA-TSC ITC BCIE Service/Feature BAND No. Numbering LAR
0 1 2 3 4 W Request Dgts Format
Subaddress
1: y y y y y n n bothept none
2: y y y y y n n rest none
3: y y y y y n n rest none
4: y y y y y n n rest none
5: y y y y y n n rest none
6: y y y y y n n rest none

 

[rgtrgt]

what are you getting when you call it? it looks like you are sending 40000 over the trunk group

 

[g3rguy]

Try not deleting any digits. In your uni you are telling it to delete the 2.

 

[g3rguy]

after reading it more, If the station in the cisco is 20000, you have your uni set up to strip the 2 then add 234, then your route strips the 23 and sends 40000, so do not delete the 2 in the uni and you can delete 3 the 234 in the route and you will be sending the 20000 to the cisco

 

[rgtrgt]

that will do it g3rguy

 

[DFM]

Thanks Folks, you have helped me out tremendously