I have a release 5.0 site that I po 1

[rheine]

I have a release 5.0 site that I posted in the past about. I have an MGC card that had the incorrect IP address within that card and I changed it to match the correct IP of the loop and shelf. I attempted to bring that MGC up this afternoon and after a long delay the display showed the correct loop and shelf. Here is my issue. I am not able to IDC that card and all of the channels on that card are disabled. I am also not able to get any other cards to work in that cabinet. This is what I was seening when that card registered:


SRPT077 IPMG[12 1]: Loadware version mismatch detected. Adding to sequential upgrade que
ue.

SRPT210 Reg GRANTED for IP[10.12.90.27] IPMG[12 1] TS[-691737569]

Can I complete a loadware version mismatch correction via element manager or do I need to replace this card?

 

[rheine]

You are correct, the MGC is NTDW60BAE5...

 

[rheine]

KCFLHRC, The following happened when I had attempted that upgrade: SRPT063 IPMG[12 1]: Unable to initiate Centralized Software Upgrade.

Should I just replace that MGC or will the gold image procedure work?

 

[KCFLHRC]

I bet the Gold Image procedure will work. It has always worked for me.

 

[KCFLHRC]

If you connect to the MGC card and watch it on boot up and it says something about missing XML file then I think the Gold Image trick will work.

 

[rheine]

I attempted that command again and this is what happened.

CCBR000
.upgmg 12 1
WARNING!!! This operation will cause a service interruption.Proceed (Y/N)? y
IPMG[12 1]: Doing Upgrade already. Upgrade command ignored.

Other IPMG(s) available for remote upgrade :
IPMG[0 0]
IPMG[0 1]
IPMG[4 0]
IPMG[4 1]
IPMG[8 0]
IPMG[8 1]
IPMG[12 0]
.upgmg stat
+-------------------------------------------------+
| IPMG SOFTWARE UPGRADE STATUS |
+-------------------------------------------------+
| Auto Sequential Software Upgrade is Enabled |
+-------------------------------------------------+
| | | |IPMG| NEEDS |
| IPMG | STATUS | LAST UPG TIME |TYPE|UPGRADE|
+-------------------------------------------------+
| 0 0 | SUCCESS| 2010/11/05 07:54:42| MGC| NO |
+-------------------------------------------------+
| 0 1 | SUCCESS| 2010/11/05 07:54:45| MGC| NO |
+-------------------------------------------------+
| 4 0 | SUCCESS| 2010/11/05 07:54:44| MGC| NO |
+-------------------------------------------------+
| 4 1 | SUCCESS| 2012/09/11 09:33:16| MGC| NO |
+-------------------------------------------------+
| 8 0 | SUCCESS| 2010/11/05 07:54:32| MGC| NO |
+-------------------------------------------------+
| 8 1 | SUCCESS| 2010/11/05 07:54:32| MGC| NO |
+-------------------------------------------------+
| 12 0 | SUCCESS| 2010/11/05 07:54:33| MGC| NO |
+-------------------------------------------------+
| 12 1 | RUNNING| 2012/09/27 15:56:54| MGC| NO |
+-------------------------------------------------+
.
SRPT077 Centralized Software Upgrade complete.


CCBR000
.upgmg stat
+-------------------------------------------------+
| IPMG SOFTWARE UPGRADE STATUS |
+-------------------------------------------------+
| Auto Sequential Software Upgrade is Enabled |
+-------------------------------------------------+
| | | |IPMG| NEEDS |
| IPMG | STATUS | LAST UPG TIME |TYPE|UPGRADE|
+-------------------------------------------------+
| 0 0 | SUCCESS| 2010/11/05 07:54:42| MGC| NO |
+-------------------------------------------------+
| 0 1 | SUCCESS| 2010/11/05 07:54:45| MGC| NO |
+-------------------------------------------------+
| 4 0 | SUCCESS| 2010/11/05 07:54:44| MGC| NO |
+-------------------------------------------------+
| 4 1 | SUCCESS| 2012/09/11 09:33:16| MGC| NO |
+-------------------------------------------------+
| 8 0 | SUCCESS| 2010/11/05 07:54:32| MGC| NO |
+-------------------------------------------------+
| 8 1 | SUCCESS| 2010/11/05 07:54:32| MGC| NO |
+-------------------------------------------------+
| 12 0 | SUCCESS| 2010/11/05 07:54:33| MGC| NO |
+-------------------------------------------------+
| 12 1 | RUNNING| 2012/09/27 15:56:54| MGC| NO |
+-------------------------------------------------+
.
SRPT077 IPMG 12 1:Received an upgrade request. Preparing IPMG for upgrade.

SRPT063 IPMG 12 1: Failed to retrieve [/u/ipmg/mgc/dnldlist.rec].Upgrade failed.


So close.

 

[rheine]

I would need to remove the TLAN and ELAN network cables to perform this gold image task, correct? I would want that isoloated from the network..Once that has been complete I would then plug those cables back in and reboot that MGC, correct?

 

[KCFLHRC]

Found another thread on this, check it out. Sounds like your problem

http://www.tek-tips.com/viewthread.cfm?qid=1687988

 

[rheine]

I looked at that thread but that would definetly ebe service effecting in the entire pbx. I will try your procedure first or replace that card.

 

[rheine]

KCFLHRC (TechnicalUser), Hopefully you are in today? I was finally able to get that MGC card removed from my site and installed it in a non-active shelf at another location. I attempted that gold image but when I seleted option 2 force csp to boot nothing happened. I selected the ? and selected the option for csp boot. I am not 100% sure that this is gold imaged. I have those results below:


Found device : INTEL 82365SL

Engcode: NTDW60BAE5 REL 03
ELAN mac address is: 00:1b:ba:fc:f7:62
TLAN mac address is: 00:1b:ba:fc:f7:61
RESET reason: Powerup Reset.
Daughter board 1: NOT INSTALLED.
Daughter board 2: NTDW62AAE5 R01 00:90:cf:06:50:37.
FPGA VERSION: AA12

Power up self test passed


VxWorks System Boot
Copyright 1984-2005 Wind River Systems, Inc.

CPU: Chagall
Version: VxWorks5.5.1
Bootcode version: MGCBAH09
Creation date: Jan 16 2008, 11:42:37


5
[VxWorks Boot]: test


SYSTEM TEST MENU
-------------------------------
Enter 'p' for Production test
or 't' for Troubleshoot
or 'd' for Daughter board test
or 's' for System power up test
or 'b' for Boot Options
Return key for exit

Enter selection:b

BOOT OPTIONS MENU
---------------------------------
0 - or return to EXIT MENU
1 - Force MSP to boot from Gold Image once
2 - Force CSP to boot from Gold Image once
3 - Force MSP to boot from Gold Image everytime
4 - Force CSP to boot from Gold Image everytime
5 - Reset Boot Options to defaults

Enter selection: 2

BOOT OPTIONS MENU
---------------------------------
0 - or return to EXIT MENU
1 - Force MSP to boot from Gold Image once
2 - Force CSP to boot from Gold Image once
3 - Force MSP to boot from Gold Image everytime
4 - Force CSP to boot from Gold Image everytime
5 - Reset Boot Options to defaults

Enter selection: 2

BOOT OPTIONS MENU
---------------------------------
0 - or return to EXIT MENU
1 - Force MSP to boot from Gold Image once
2 - Force CSP to boot from Gold Image once
3 - Force MSP to boot from Gold Image everytime
4 - Force CSP to boot from Gold Image everytime
5 - Reset Boot Options to defaults

Enter selection: 2

BOOT OPTIONS MENU
---------------------------------
0 - or return to EXIT MENU
1 - Force MSP to boot from Gold Image once
2 - Force CSP to boot from Gold Image once
3 - Force MSP to boot from Gold Image everytime
4 - Force CSP to boot from Gold Image everytime
5 - Reset Boot Options to defaults

Enter selection: 2

BOOT OPTIONS MENU
---------------------------------
0 - or return to EXIT MENU
1 - Force MSP to boot from Gold Image once
2 - Force CSP to boot from Gold Image once
3 - Force MSP to boot from Gold Image everytime
4 - Force CSP to boot from Gold Image everytime
5 - Reset Boot Options to defaults

Enter selection: 0


SYSTEM TEST MENU
-------------------------------
Enter 'p' for Production test
or 't' for Troubleshoot
or 'd' for Daughter board test
or 's' for System power up test
or 'b' for Boot Options
Return key for exit

Enter selection:b

BOOT OPTIONS MENU
---------------------------------
0 - or return to EXIT MENU
1 - Force MSP to boot from Gold Image once
2 - Force CSP to boot from Gold Image once
3 - Force MSP to boot from Gold Image everytime
4 - Force CSP to boot from Gold Image everytime
5 - Reset Boot Options to defaults

Enter selection: 2

BOOT OPTIONS MENU
---------------------------------
0 - or return to EXIT MENU
1 - Force MSP to boot from Gold Image once
2 - Force CSP to boot from Gold Image once
3 - Force MSP to boot from Gold Image everytime
4 - Force CSP to boot from Gold Image everytime
5 - Reset Boot Options to defaults

Enter selection: 2

BOOT OPTIONS MENU
---------------------------------
0 - or return to EXIT MENU
1 - Force MSP to boot from Gold Image once
2 - Force CSP to boot from Gold Image once
3 - Force MSP to boot from Gold Image everytime
4 - Force CSP to boot from Gold Image everytime
5 - Reset Boot Options to defaults

Enter selection: 2

BOOT OPTIONS MENU
---------------------------------
0 - or return to EXIT MENU
1 - Force MSP to boot from Gold Image once
2 - Force CSP to boot from Gold Image once
3 - Force MSP to boot from Gold Image everytime
4 - Force CSP to boot from Gold Image everytime
5 - Reset Boot Options to defaults

Enter selection: 2

BOOT OPTIONS MENU
---------------------------------
0 - or return to EXIT MENU
1 - Force MSP to boot from Gold Image once
2 - Force CSP to boot from Gold Image once
3 - Force MSP to boot from Gold Image everytime
4 - Force CSP to boot from Gold Image everytime
5 - Reset Boot Options to defaults

Enter selection: 0


SYSTEM TEST MENU
-------------------------------
Enter 'p' for Production test
or 't' for Troubleshoot
or 'd' for Daughter board test
or 's' for System power up test
or 'b' for Boot Options
Return key for exit

Enter selection:B
[VxWorks Boot]: b
Unrecognized command. Type '?' for help.
[VxWorks Boot]: b
Unrecognized command. Type '?' for help.
[VxWorks Boot]: 2
Unrecognized command. Type '?' for help.
[VxWorks Boot]: 2
Unrecognized command. Type '?' for help.
[VxWorks Boot]: exit


[VxWorks Boot]: exit


[VxWorks Boot]: 0
Unrecognized command. Type '?' for help.
[VxWorks Boot]: ?

? - print this list
r - write to flash (Loaded image at Addr = 0x100000)
z [startaddr] - Load Image over serial (default Addr = 0x100000)
@ - boot MSP & CSP
p - print boot params
c - change boot params
l - boot MSP & CSP
d adrs[,n] - display memory
m adrs - modify memory
f adrs, nbytes, value - fill memory
t adrs, adrs, nbytes - copy memory
test - test menu
e - print fatal exception
v - print boot logo with version
reboot - reboots the card

[VxWorks Boot]: p

boot device : ata=0,0
unit number : 0
processor number : 0
file name : /p/mainos.sys
inet on ethernet (e) : 10.12.90.27:ffffff00
gateway inet (g) : 10.12.90.49
flags (f) : 0x22
target name (tn) : MGC
other (o) : eln


Product Code : NTDW60BAE5
Serial No. : NNTMG19Y5B6D
Revision No. : 3
[VxWorks Boot]: @
Loading MSP from CF...1717100

Booting ARM0 (MSP) at 0x00000100 ...
Loading Gold CSP image

Booting ARM1 (CSP) at 0x80010000 ...

Q
usrAtaInit
usrAtaInit done
Found device : INTEL 82365SL
pccardAtaEnabler: Adding block device 0x0x87918604: /dev/hda
/p/ - Volume is OK
/p1/ - Volume is OK
/u/ - Volume is OK
/e/ - Volume is OK
Host Name: bootHost
User: target
Attaching interface lo0... done
Attached IPv4 interface to eln unit 0


]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R)
] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]]
]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]]
]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]]
]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]]
]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]]
]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]]
]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]]
]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System
]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks version 5.5.1
]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.6
]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2003

CPU: Chagall. Processor #1.
Memory Size: 0x79ec000. BSP version 1.3/0.
WDB Comm Type: WDB_COMM_NETWORK
WDB: Ready.

FPGA VERSION is 41413132 AA12
No ELAN carrier found!
No TLAN carrier found!
MGC GOLD Image
mgccad25 Wednesday April 25 2007 23:02:56 EDT

*** To invoke install menu or bypass loadware upgrade enter CONTROL-I ***
Init ISEC succeeded

Should I be all set to plug this MGC card back into that 1000E release 5.0? It looks like my IP address is still programmed in this card. Technically all that I need to do is plug this MGC card back into loop 12 slot 1 and the ELAN/ TLAN cables and it should read off the C.S., correct? Thanks

 

[KCFLHRC]

Yep, plug it back in and see if it upgrades it's loadware.

 

[KCFLHRC]

Did you do all the steps? Looks like to me you left out the bottom portion to format after step 9 you need to do the format.

1. Reboot the MGC Card
2. as it is booting type <CTRL> B just after the creation date is printed and the
{VxWorks Boot} prompt should be displayed.
3. at the prompt type in “test”
4. choose option b to change boot options
5. select option 2 to force csp to boot from gold image once
6. select option 0 to return to previous menu
7. press return key to exit menu and return to prompt
8. enter @ at the prompt
9. the mgc will boot to the gold image

To format the compact flash from the gold image you must press <CTRL> I when prompted during the MGC gold boot. This will bring up a VxWorks prompt ->, At the prompt enter, diskformat “all” This will format the MGC’s internal compact flash. Reboot the MGC and when it registers to the call server it will automatically upgrade.

 

[KCFLHRC]

I don't think you did the procedure correctly. After step 6 you should have hit the return key to get back to the prompt. Then enter @ to reboot the card. Then while it is booting you enter CTRL I and do the procedure at the bottom of the page.

 

[rheine]

Ok, I will try that in the morning and keep you posted.. Thanks

 

[rheine]

KCFLHRC (TechnicalUser), I did come in early and believe that I had succeded in creating that gold image on my MGC card. The below is what I see when this MGC boots up. Now I would need to assign IP address 10.12.90.27 to this card again, correct. I am not getting that option when I press control I. It looks like I am missing a step someplace again?

Found device : INTEL 82365SL

Engcode: NTDW60BAE5 REL 03
ELAN mac address is: 00:1b:ba:fc:f7:62
TLAN mac address is: 00:1b:ba:fc:f7:61
RESET reason: Powerup Reset.
Daughter board 1: NOT INSTALLED.
Daughter board 2: NTDW62AAE5 R01 00:90:cf:06:50:37.
FPGA VERSION: AA12

Power up self test passed


VxWorks System Boot
Copyright 1984-2005 Wind River Systems, Inc.

CPU: Chagall
Version: VxWorks5.5.1
Bootcode version: MGCBAH09
Creation date: Jan 16 2008, 11:42:37


5
auto-booting...

Loading Gold MSP image

Booting ARM0 (MSP) at 0x00000100 ...
Loading Gold CSP image

Booting ARM1 (CSP) at 0x80010000 ...

Q
usrAtaInit
usrAtaInit done
Found device : INTEL 82365SL
pccardAtaEnabler: Adding block device 0x0x87918604: /dev/hda
/p/ - Volume is OK
/p1/ - Volume is OK
/u/ - Volume is OK
/e/ - Volume is OK
Host Name: bootHost
User: target
Attaching interface lo0... done
Attached IPv4 interface to eln unit 0


]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R)
] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]]
]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]]
]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]]
]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]]
]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]]
]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]]
]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]]
]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System
]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks version 5.5.1
]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.6
]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2003

CPU: Chagall. Processor #1.
Memory Size: 0x79ec000. BSP version 1.3/0.
WDB Comm Type: WDB_COMM_NETWORK
WDB: Ready.

FPGA VERSION is 41413132 AA12
SM: Decomissioning the data files.
No ELAN carrier found!
No TLAN carrier found!
SM: A default system password storage has been created.
MGC GOLD Image
mgccad25 Wednesday April 25 2007 23:02:56 EDT

*** To invoke install menu or bypass loadware upgrade enter CONTROL-I ***
3
Control I detected. To change configuration enter mgcsetup
-> Init ISEC succeeded

-> ??
syntax error
->

 

[rheine]

Disregard, I answered my own question..... I will keep you posted..

 

[janaya]

if you disable secure transfers it won't do anything to the call server. Just go to ld 117 and disable, then go to 143 and run your upgrade. Once that is done you can enable the secure transfers. I've done this when updating firmware and haven't had any issues.

 

[rheine]

All, the gold image did not get me any farther. I am suspecting that this MGC card can not be recovered. Would everyone recommend that I replace this MGC card at this time?

The below is what happened today: (getting this MGC to register correctly should not be this difficult)

>
SRPT077 IPMG[12 1]: Loadware version mismatch detected. Adding to sequential upgrade que
ue.

SRPT210 Reg GRANTED for IP[10.12.90.27] IPMG[12 1] TS[691219015]


SRPT063 IPMG[12 1]: Unable to initiate Centralized Software Upgrade.
.upgmg stat
+-------------------------------------------------+
| IPMG SOFTWARE UPGRADE STATUS |
+-------------------------------------------------+
| Auto Sequential Software Upgrade is Enabled |
+-------------------------------------------------+
| | | |IPMG| NEEDS |
| IPMG | STATUS | LAST UPG TIME |TYPE|UPGRADE|
+-------------------------------------------------+
| 0 0 | SUCCESS| 2010/11/05 07:54:42| MGC| NO |
+-------------------------------------------------+
| 0 1 | SUCCESS| 2010/11/05 07:54:45| MGC| NO |
+-------------------------------------------------+
| 4 0 | SUCCESS| 2010/11/05 07:54:44| MGC| NO |
+-------------------------------------------------+
| 4 1 | SUCCESS| 2012/09/11 09:33:16| MGC| NO |
+-------------------------------------------------+
| 8 0 | SUCCESS| 2010/11/05 07:54:32| MGC| NO |
+-------------------------------------------------+
| 8 1 | SUCCESS| 2010/11/05 07:54:32| MGC| NO |
+-------------------------------------------------+
| 12 0 | SUCCESS| 2010/11/05 07:54:33| MGC| NO |
+-------------------------------------------------+
| 12 1 | FAILED| 2012/10/04 15:11:37| MGC| NO |
+-------------------------------------------------+

+-------------------------------------------------+
.upgmg 12 1
WARNING!!! This operation will cause a service interruption.Proceed (Y/N)? y


IPMG[12 1]: Lost contact. Upgrade command ignored.

Other IPMG(s) available for remote upgrade :
IPMG[0 0]
IPMG[0 1]
IPMG[4 0]
IPMG[4 1]
IPMG[8 0]
IPMG[8 1]
IPMG[12 0]
..upgmg stat
+-------------------------------------------------+
| IPMG SOFTWARE UPGRADE STATUS |
+-------------------------------------------------+
| Auto Sequential Software Upgrade is Enabled |
+-------------------------------------------------+
| | | |IPMG| NEEDS |
| IPMG | STATUS | LAST UPG TIME |TYPE|UPGRADE|
+-------------------------------------------------+
| 0 0 | SUCCESS| 2010/11/05 07:54:42| MGC| NO |
+-------------------------------------------------+
| 0 1 | SUCCESS| 2010/11/05 07:54:45| MGC| NO |
+-------------------------------------------------+
| 4 0 | SUCCESS| 2010/11/05 07:54:44| MGC| NO |
+-------------------------------------------------+
| 4 1 | SUCCESS| 2012/09/11 09:33:16| MGC| NO |
+-------------------------------------------------+
| 8 0 | SUCCESS| 2010/11/05 07:54:32| MGC| NO |
+-------------------------------------------------+
| 8 1 | SUCCESS| 2010/11/05 07:54:32| MGC| NO |
+-------------------------------------------------+
| 12 0 | SUCCESS| 2010/11/05 07:54:33| MGC| NO |
+-------------------------------------------------+
| 12 1 | FAILED| 2012/10/04 15:11:37| MGC| NO |
+-------------------------------------------------+



SRPT077 Centralized Software Upgrade complete.

I just need to add the correct IP address in the new MGC card and I should be able to plug this back in as is, correct? Thanks

 

[KCFLHRC]

I suppose the card could be bad. Maybe try Janaya's fix. Worth a shot.

 

[rheine]

It seems like the card replacement might be easier at this point. This is a hospital and they can't afford to go down. I have not done this transfer procedure before and would not feel comfortable attempting that on a live system. I will replace this card sometime next week and keep everyone posted. If that does not work I will need to try something else....

 

[rheine]

Great news everyone! I also want to thank everyone for their help especially KCFLHRC (TechnicalUser). Luckily replacing the MGC card took care of the issue. The below is what transpired during this card replacement via the PBX: (I completed all IP setting at this site instead of another PBX)

1
auto-booting...

Loading MSP from CF...1752052
Booting ARM0 (MSP) at 0x00000100 ...

Loading CSP from CF...8364032 + 4706304
Booting ARM1 (CSP) at 0x80010000 ...

Q
usrAtaInit
usrAtaInit done
Found device : INTEL 82365SL
pccardAtaEnabler: Adding block device 0x0x879053ac: /dev/hda
/p/ - Volume is OK
/p1/ - Volume is OK
/u/ - Volume is OK
/e/ - Volume is OK
Host Name: bootHost
User: target
Attaching interface lo0... done
Attached IPv4 interface to eln unit 0
Loading symbol table from /p/mainos.sym ...done


]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R)
] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]]
]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]]
]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]]
]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]]
]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]]
]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]]
]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]]
]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System
]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks version 5.5.1
]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.6
]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2003

CPU: Chagall. Processor #1.
Memory Size: 0x79ea800. BSP version 1.3/0.
WDB Comm Type: WDB_COMM_NETWORK
WDB: Ready.

FPGA VERSION is 41413136 AA16
Part of MGC loadware MGCFAA16
08/10/2012 14:49:48 LOG0006 tRootTask: trBufLib_init OK, memory at 0x83f95994 of size 43650716
08/10/2012 14:49:48 LOG0006 tRootTask: TR Memory Library initialization Ok
08/10/2012 14:49:48 SRPT0730 OS 0: Cold Start
Release: MGCCAP01
Created: Monday November 23 2009 18:24:54 EST
SEC0119 Local authentication is being used
08/10/2012 14:49:51 SEC0119 Local authentication is being used.
Retrieved old volume params with %80 confidence:
Volume Parameters: FAT type: FAT16, sectors per cluster 116
105 FAT copies, 0 clusters, 29786 sectors per FAT
Sectors reserved 24946, hidden 1634100580, FAT sectors 3127530
Root dir entries 29556, sysId (null) , serial number 745f636f
Label:" 2 1 " ...
Disk with 100 sectors of 512 bytes will be formatted with:
Volume Parameters: FAT type: FAT12, sectors per cluster 1
2 FAT copies, 90 clusters, 1 sectors per FAT
Sectors reserved 1, hidden 0, FAT sectors 2
Root dir entries 112, sysId VXDOS12 , serial number 745f636f
Label:" 2 1 " ...
No breakpoints
08/10/2012 14:49:52 SRPT0107 Hardware reset reason = Hard Reset [register value = 0x0]

Loading patch files in /p/patch
Loading patch from "/p/patch/p29519_1.mgc"
Patch handle is: 0
Loading patch from "/p/patch/p29520_1.mgc"
Patch handle is: 1
Loading patch from "/p/patch/p29531_1.mgc"
Patch handle is: 2
Loading patch from "/p/patch/p29575_1.mgc"
Patch handle is: 3
Patch 0 has been activated successfully.

Patch 1 has been activated successfully.

Patch 2 has been activated successfully.

Patch 3 has been activated successfully.

4 patches from /p/patches loaded & activated.
### sshServerManager: info [sshServerManagerGenerateNewActiveKey] Key generation has been started. This may take some time to comple
te.
08/10/2012 14:50:04 LOG0006 applStart: mgcConfigStart initialization succeeded
08/10/2012 14:50:04 LOG0006 applStart: Task mgcSysSpawn enters initialization
08/10/2012 14:50:05 LOG0006 applStart: Task mgcSysSpawn initialization succeeded
08/10/2012 14:50:05 LOG0006 MGCSYS: Xmsg Daemon task spawn is successful
08/10/2012 14:50:07 LOG0006 applStart: mdioSemCreate initialization succeeded
08/10/2012 14:50:08 LOG0006 applStart: mgcImageVerRead initialization succeeded
08/10/2012 14:50:08 LOG0006 applStart: mgcSysUtilSpawn initialization succeeded
08/10/2012 14:50:08 LOG0006 applStart: tlanInit initialization succeeded
08/10/2012 14:50:08 LOG0006 applStart: sysInfoFlashInit initialization succeeded
08/10/2012 14:50:08 LOG0006 applStart: gwcA31Main initialization succeeded
08/10/2012 14:50:08 LOG0006 applStart: vapiLayerInit initialization succeeded
08/10/2012 14:50:08 LOG0006 applStart: afsInitialize initialization succeeded
08/10/2012 14:50:08 LOG0006 applStart: afsSubscriberInit initialization succeeded
08/10/2012 14:50:08 LOG0006 applStart: afsPublisherInit initialization succeeded
08/10/2012 14:50:08 LOG0006 applStart: Init ISEC succeeded
08/10/2012 14:50:08 LOG0006 applStart: mamISECStart initialization succeeded
08/10/2012 14:50:08 LOG0006 applStart: tncInit initialization succeeded
08/10/2012 14:50:09 LOG0006 applStart: mgcStartUp initialization succeeded
08/10/2012 14:50:09 LOG0006 applStart: mgcClanInit initialization succeeded
08/10/2012 14:50:09 LOG0006 applStart: mgcInitRegister initialization succeeded
08/10/2012 14:50:09 LOG0006 applStart: mgcVgwAppStart initialization succeeded
08/10/2012 14:50:09 LOG0004 tMgcVgwAppStart: DSP DBs are present, waiting for mgcdb.xml from Primary Call Server
08/10/2012 14:50:09 LOG0006 MGCUTIL: IPMG Cabinet is non-MG1010
08/10/2012 14:50:10 LOG0006 applStart: portAccessInit initialization succeeded
08/10/2012 14:50:10 LOG0006 applStart: securityDomainElemPropValueSet initialization succeeded
08/10/2012 14:50:10 LOG0006 tIpExpStartup: Registered successfully to Primary Call Server[10.12.90.10]
08/10/2012 14:50:10 LOG0006 tIpExpStartup: Received configuration data from Primary Call Server on attempt[1]
08/10/2012 14:50:18 SRPT0017 OMM: IP link is UP between Primary Call Server and IPMG[12 1]
08/10/2012 14:50:19 LOG0006 TNC: CHANNEL CREATION SUCCESSFUL

08/10/2012 14:50:20 LOG0006 CLAN: Slot: 1, Card Type: XDLC (17), Signaling Type: X12 (1), Map Type: 3
08/10/2012 14:50:25 LOG0006 tConfigProcess: AlarmConfigClient Registered with CP successfully

08/10/2012 14:50:25 LOG0006 tConfigProcess: Server socket closed

08/10/2012 14:50:25 LOG0006 tConfigProcess: Opened Server socket

08/10/2012 14:50:26 LOG0006 SYS: VGW5000 Card initialized, all alarms cleared. (202)
08/10/2012 14:50:26 LOG0001 SYS: VGW1036 Call server communication link: 10.12.90.10 down (20)
08/10/2012 14:50:26 LOG0006 SYS: Waiting for PBX RUDP link to be established, timeout is set to 2 seconds retry 0
08/10/2012 14:50:28 LOG0006 SYS: PBX RUDP link established
08/10/2012 14:50:28 LOG0006 SYS: VGW5036 Call server communication link: 10.12.90.10 up (20)
08/10/2012 14:50:29 LOG0006 VGW: DSP DB 2 is Low Density
08/10/2012 14:50:29 LOG0006 VGW: Current VLAN Table is 0
08/10/2012 14:50:29 LOG0006 VGW: Change to Reset Mode: Current VLAN Table is 4
08/10/2012 14:50:30 LOG0006 VGW: Change to Normal Mode: Current VLAN Table is 0
08/10/2012 14:50:31 LOG0006 VGW: Current VLAN Table is in NORMAL mode: 0,

08/10/2012 14:50:31 LOG0006 VGW: VGW5014 Ethernet carrier: eth0, OK (9)
08/10/2012 14:58:36 LOG0006 CLAN: Slot: 1, Card Type: XDLC (17), Signaling Type: X12 (1), Map Type: 3

I will close this thread now.....