how to move cards 2

[electrobank]

Hi there people... new question...
here's what i have; Meridian 1 version 2111 release 22 issue 46+ that has 3 cabinets installled. cabinet 1 have DTI Cards, meridian mail, and some line and trunk cards, cabinet 2 has line card and cabinet 3 only have 2 line cards (both analog) the cabinets connect using a fiber module that goes from 1 to 2 and from 2 to 3.
and the question. i want to remove the line cards from cabinet 3 and move them to empty slots in cabinet 1 and 2 and finally i want to remove cabinet 3 from the room. how do i do that?
i appreciate as much details as possible.

 

[johnpoole]

ld 25
mov

works good, i used it just last week in an older opt 11

john poole
bellsouth business
columbia,sc

 

[electrobank]

ok. just to clarify. ld 25 then mov... and my questions
>the system ask me wich card and where to?
>this move includes all the TN information associated with the move?
> finally: after moving the 2 cards, can i just shut down that cabinet or i need to do something else?

 

[Johnthephoneguy]

You will also have to move your pigtail that goes to the MDF or run new jumpers.

probably easiest to unplug them from the bottom of the 3rd cabinet and move them to the new spots.

JohnThePhoneGuy

"If I can't fix it, it's not broke!

 

[johnpoole]

yep.. second post is also correct.. either move the switch tail or 16 jumpers

john poole
bellsouth business
columbia,sc

 

[electrobank]

and what about the empty cabinet? just power off?

 

[electrobank]

Guys... I was about to do the card move and i realized the followng...
> how do i disable the empty cabinet? i just need 2 and the 3 will be removed and stored.
> the cards can be moved while the PABX is on? or i need to do the ld 25 and then shut down and move?

i'll run new jumpers because later i'll have the panel relocated and need to punch down all the cables from the PABX to the panel.

 

[phonz1]

when all cards are moved, shut down the old cabinet. Also, I would not use the mov command with any cards that have ACD on them, best to out the acd, mov the card and then rebuild the acd.

Depending on your environment, all is safe to do during regular hours as long as you let everyone know!

 

[electrobank]

What is this ACD? here's a print out of my extension...
and about the last cabinet... just pull the plug and disconnect the Fiber that goes from the main cabinet to the empty cabinet is OK???? i just want to double and triple check before i start this process...
DES PRUEBA
TN 005 0 00 00
TYPE 2616
CDEN 8D
CUST 0
AOM 0
FDN 7000
TGAR 0
LDN NO
NCOS 4
RNPG 10
SCI 0
SSU
LNRS 16
XLST 1
SCPW
SFLT NO
CAC 0
CLS TLD FBA WTA LPR PUA MTA FNA HTA ADD HFA
MWA AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD CCSA-CSI SWD LNA CNDA
CFTD SFD DDV CNID
ICDD CDMD LLCN MCTD CLBD AUTU
GPUD DPUA DNDA CFXA ARHD CLTD ASCD
CPFD CPTD ABDD DELD CFHD FICD NAID
UDI RCC HBTD AHA DDGA NAMA PRSD NRWD NRCD NROD
USRD ULAD OCBD
CPND_LANG ENG
RCO 0
HUNT 7000
LHK 1
PLEV 02
AST
IAPG 0
ITNA NO
DGRP
DNDR 0
KEY 00 SCR 2435 MARP
CPND
NAME HUMBERTO PORTILLO
XPLN 27
DISPLAY_FMT FIRST,LAST
01 SCR 3435 MARP
CPND
NAME HUMBERTO PORTILLO
XPLN 27
DISPLAY_FMT FIRST,LAST
02 AO6
03 TRN
04 CFW 16 2261
05 MWK 7000
06 RGA
07
08 SCN 2261
CPND
NAME SERVER ROOM
XPLN 27
DISPLAY_FMT FIRST,LAST
09 ADL 16 472435
10
11
12 RNP
13 SSU 0010
14 DSP
15
DATE 1 APR 1993

 

[phonz1]

to disconnect the fiber you'd need to pull the SSC card and that will take down the switch. So you'll want to schedule that, but it will not hurt to let it dangle there for awhile.

Acd, is set that are in a call center. Key 0 would be programmed as:

KEY 00 ACD 2435 0 XXXX MARP
CPND
NAME HUMBERTO PORTILLO
XPLN 27
DISPLAY_FMT FIRST,LAST

 

[electrobank]

OK... So from what i have no ACD is programmed on the lines... and the Fiber needs to be pulled with the switch off... i can do that late nigth... I hope i'm no naggin' with my questions but... i'll shut down... remove the fiber connected betwee 1 and 3 and turn on the switch... nothing more...

 

[phonz1]

that will work too!