How to change XLST in an 81c

[Comtech2009]

Hi I'm a newbie at this and learning as I go. I enherith this switch and it has taken a while to find out the basics in and outs of it but it's being very interesting. I have a new challenge that I'm bumping my head to the wall. I was asked to change the system speed dial number 58 to dial an ext for a manager and I don't know how to print and change this. I know ld 18 is where you create a new one but what I need is to change where this particular one routes to. for example if anybody dials 55 it goes to ext 8600 which is the operator, if they dial 56 it goes to the spa 1856 etc. etc. I know that the whole system uses xlst 3. Can someone guide me Plase!!

 

[GHTROUT]

I doubt there is XLST involved. Print the Speed Lists in LD20

REQ PRT TYPE SCL

Then Change type SCL in LD18

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[telebub]

If it's a System Speed list, Change type SSC in LD 18. Hit return to STOR. Enter 58 [space] the manager's number. Hit return back to REQ.

War Eagle!
Lions Baseball '09!

 

[GHTROUT]

Ah yes, I see it was System Speed. So everything I said was SCL "Speed Call List" is really SSC for "System Speed Call"


~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[Comtech2009]

I did go to LD 20 and:

req prt
type scl
<enter>

But it goes for ever and I can't really know where this is. But to give you an Idea of how most phones are programmed here is en example:

PS. I don't have a pc hooked up to the switch I have a dummy terminal VT520 so I can't do a file capture.

DES FRTDSK
TN 28 1 04 06
TYPE 3903
CDEN 8D
CTYP XDLC
CUST 0
FDN 1689
TGAR 1
LDN NO
NCOS 5
SGRP 0
RNPG 2
SCI 0
SSU 0088
LNRS 16
XLST 3
CLS CTD FBD ETC. ETC. ETC
CPND_LANG ENG
RCO 0
HUNT 1689
LHK 1
LPK 2
PREV 02
CSDN
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
MLNG ENG
DNDR 0
KEY 00 SCR 1504



KEY 16 MWK 1689
KEY 17 TRN
KEY 18 AO6
KEY 19 CFW 4
KEY 21 PRK
KEY 22 RNP



I DID A LIST ON SSC 0088 AND IS 500 LONG SO I DON'T KNW HOW TO GO ABOUT THIS !!!HELP!!!!

 

[telebub]

In LD 20:

REQ: PRT
TYPE: SCL
LSNO: 3
RNGE: (hit return)

This will show all entries in list 3. See if Bin 58 is the one you want to change.

Go to LD 18:
REQ: CHG
TYPE: SCL
LSNO: 3
(hit return to STOR)
STOR: 58 [space] xxxx

See if that works.

War Eagle!
Lions Baseball '09!

 

[Comtech2009]

Ok I went to LD 20 and did:

REQ PRT
TYPE SCL
LSNO 3
RANGE <RETUR>



AND THIS IS WHAT CAME UP


DNSZ 4
STOR 0
STOR 1
STOR 2 8529
STOR 3 6037
STOR 4 695
STOR 5 679
STOR 6
STOR 7
STOR 8
STOR 9


REQ:

 

[telebub]

Oh, ok. It is a pretranslation list. Try this:

In LD 20:

REQ: PRT
TYPE: PRE
CUST: 0

Post what you get from that.

War Eagle!
Lions Baseball '09!

 

[Comtech2009]

Ok so I did:

LD 20
REQ PRT
TYPE PRE
CUST 0
<ENTER>

PRE
CUST 0
XLAT 0
PRE 0
XLAT 1
PRE 1
XLAT 2
PRE 2
XLAT 3
PRE 3
XLAT 4
PRE 4
XLAT 5
PRE 5
XLAT 6
PRE 6
XLAT 7
PRE 7
XLAT 8
PRE 298
XLAT 9
PRE 299

REQ:

 

[telebub]

Is it too much trouble to print and post SCL lists 0-9?

So the users dial 58 directly, they do not press the System Speed button 1st? I just want to make sure we are dealing with pretranslation and not system speed.



War Eagle!
Lions Baseball '09!

 

[Comtech2009]

Yes you are correct. There's no need to press *1 or anything else. How do I print these list?

 

[telebub]

LD 20
REQ: PRT
TYPE: SCL
LSNO: x (do 0 through 9 one at a time)
RNGE: (hit return)

Before posting, look through all of the lists. See if you can figure out where 55 dials 8600 and 56 dials 1856. That might tell you what 58 is doing and where you need to change it.


War Eagle!
Lions Baseball '09!

 

[Comtech2009]

Thanks this might take a bit longer and I'm almost out the door but I'll start and post back tomororow when I get back on it.

Thanks for all the help today I really apreciate it finally I feel I'm geting somewhere.