I have a g450 being installed as just a new media gateway with no s8300 at my main site to feed some new floors digital and analog phones. The gateway will be setup to link to my s8730's. how do I make sure no IP phones in the firm ever register to this gateway?
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
g450
- Thread starter btrain08
- Start date
phoneguy55
Programmer
They wont. IP phones register to CLAN's or S8XX0's.
- Thread starter
- #3
- Thread starter
- #4
Yes, the 2 LAN ports are 10/5 and 10/6. You can set them up for "redundant" operation (if one cable or port dies, the other one takes over). "ETR" is "Emergency Transfer Relay", used to run an 808A transfer panel, "CCA" is a "Contact Closure Adjunct" and is used to connect a relay for a doorbox (uses a Partner relay module, model 950A1, COMCODE: 107881435)
ETR: page 30
CCA: page 31
CLIENT-G450-001(super)# show port
Port Name Status Vlan Level Neg Dup. Spd. Type
------ ---------------- --------- ---- ------ ------- ---- ---- ----------------
10/5 LAN1 connected 1 0 disable full 100M Avaya Inc., G450
Media Gateway 10/100/1000BaseTx Port 10/5
10/6 LAN2 disabled 1 0 disable full 100M Avaya Inc., G450
Media Gateway 10/100/1000BaseTx Port 10/6
CLIENT-G450-001(super)#
CLIENT-G450-001(super)# show port redundancy
Redundancy Name Primary Port Secondary Port Status
----------------- -------------- ---------------- --------
LAN-Redundancy 10/5 10/6 primary
Minimum Time between Switchovers: 1
Switchback interval: 0
CLIENT-G450-001(super)#
Mitch
AVAYA Certified Expert
ETR: page 30
CCA: page 31
CLIENT-G450-001(super)# show port
Port Name Status Vlan Level Neg Dup. Spd. Type
------ ---------------- --------- ---- ------ ------- ---- ---- ----------------
10/5 LAN1 connected 1 0 disable full 100M Avaya Inc., G450
Media Gateway 10/100/1000BaseTx Port 10/5
10/6 LAN2 disabled 1 0 disable full 100M Avaya Inc., G450
Media Gateway 10/100/1000BaseTx Port 10/6
CLIENT-G450-001(super)#
CLIENT-G450-001(super)# show port redundancy
Redundancy Name Primary Port Secondary Port Status
----------------- -------------- ---------------- --------
LAN-Redundancy 10/5 10/6 primary
Minimum Time between Switchovers: 1
Switchback interval: 0
CLIENT-G450-001(super)#
Mitch
AVAYA Certified Expert
- Thread starter
- #6
Sorry to be a pest.. I configured 10/5-6 for 100 full duplex.. I tried 1GB, but it spit back an operation failed message. I used the setup wizard to set my vlan and ip info as well as the 4 address in my mgc list.
Can you tell me the sequence for the port redundancy commands? Once I do that I should be able to connect up to my network and do my PBX translations?
I don't put IP addresses on the 2 LAN ports do I.. just the one I entered in the setup?
Can you tell me the sequence for the port redundancy commands? Once I do that I should be able to connect up to my network and do my PBX translations?
I don't put IP addresses on the 2 LAN ports do I.. just the one I entered in the setup?
- Status
Similar threads
- Locked
- Question