Error Message and How to Resolve SCH0120 Error 2

[havertyj]

I am trying to out a TN and then re-create it as a IP phone. I have done this with about five other numbers without any problem. The error I receive is SCH0120 which is "Wrong number of input fields to DSL or TN prompt". Below is information about the phone I am trying to out if someone could please provide some troubleshooting steps:

DES 3319
TN 056 1 03 00
TYPE 3904
CDEN 8D
CTYP XDLC
CUST 0
MRT
ERL 0
FDN 1700
TGAR 1
LDN NO
NCOS 6
SGRP 0
RNPG 74
SCI 0
SSU
LNRS 16
XLST
CLS CTD FBD WTA LPR PUA MTD FNA HTA TDD HFA GRLD CRPA STSD
MWA LMPN RMMD AAD IMD XHD IRA NID OLA VCE DRG1
POD SLKD CCSD SWD LNA CNDA
CFTD SFA MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDD CDMD LLCN MCTD CLBD AUTU
GPUD DPUD DNDA CFXD ARHA CLTD ASCD
CPFA CPTA ABDD CFHD FICD NAID BUZZ AGRD MOAD AHD
DDGA NAMA
DRDD EXR0
USMD USRD ULAD RTDD RBDD RBHD PGND OCBD FLXD FTTC MCBN
CDMR PRED RECD MCDD T87D SBMD
PKCH CROD ELCD
CPND_LANG ENG
RCO 0
HUNT 1700
LHK 1
LPK 2
PLEV 02
PUID
UPWD
DANI NO
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
MLNG ENG
DNDR 0
KEY 00 SCR 1154 0 MARP
CPND
NAME UNIVERSITY RELATIONS
XPLN 27
DISPLAY_FMT FIRST,LAST
01 SCR 51154 D MARP
CPND
NAME UNIVERSITY RELATIONS
XPLN 27
DISPLAY_FMT FIRST,LAST
02
03
04
05
06
07 ADL 16
08 ADL 16
09 ADL 16 1711
10 ADL 16 2151
11
12
13
14
15
16 MWK 1700
17 TRN
18 AO6
19 CFW 4
20
21
22 RNP
23
24
25
26
27 CLT
28 RLT
29
30
31
DATE 27 JAN 2014

Trying to out the line as follows:

PT0000
REQ: OUT
TYPE: 3904
TN 056 1 03 00
SCH0120
TN

Results in the SCH0120 error. I do not see anything on this line that is different from other lines that I have outed. Any suggestions?

Thank you!

 

[trvlr1]

Try typing the TN as 56 1 3 0 with single spaces between the numbers.

 

[havertyj]

That did it! Thank you! I had not had to do that with other TNs we outed. The error message was not obvious either. After using 56 1 3 0 it outed as expected. Thank you again! If you can explain why it would not take 056 1 03 00 and instead had to be entered as 56 1 3 0, I would appreciate the information.

John

 

[30n30w]

For some things there is simply no explanation. One GK instructor teaching us about the inconsistencies between LD's (like defaults for example - some you can enter through CUST, (default 0) and others you can't... )

When asked why things were different, odd, or just plain crazy when it came to Nortel; he had a simple answer:
he would shrug, and say "Canadians on Crack!" as his explanation of the Nortel Programmers.

So that's it - "Canadians on Crack".....there's your explanation....

(no offense to those Canadians or those Canadians NOT on crack.....)

 

[havertyj]

Understood.... The software we use to program our switch (RSI MerAssistant) is also created by those up North. Works most of the time and then other times it freaks out when the switch replies back with something it is not expecting.

Thanks all!

 

[jamie2]

That's why its best to utilize scripts in Procomm or ZOC. If it doesn't work, is because you did it correctly and not someone Else's programming that is much harder to find the error.