Draytel Sip Trunks

[bizsoftware1]

Hi,

has anybody succesfully setup draytel sip trunks, i am trying to setup on SOE I have added license but cannot get it to work, just wondered if anyone has done it and can lead me.

They do not run stun server, settings;
How do I set up other products for DrayTEL ?
The setup of your equipment or software will depend on that product and you should refer to its own documentation. The information you need is normally :

Registrar : draytel.org
SIP port : 5060
Username : 8xxxxx (the numeric part of your DrayTEL account, before the @draytel.org)
Outgoing Proxy : nat.draytel.org:5065 - Note : This should not be used unless your VoIP device is behind another firewall - only use it if that is the case and try without first. The Port number and outgoing proxy name might be entered separately, depending on the VoIP device you're using.

Is there an outgoing Proxy for DrayTEL ?
Yes. If you are using your SIP device behind a firewall, or NAT device, you may need to use the DrayTEL proxy instead of accessing DrayTEL in direct mode. To do this, set your outgoing proxy to nat.draytel.org:5065 (the exact method will depend on your VoIP/SIP device. Do not use the proxy if your VoIP device is on a public IP address. DrayTEL does not operate a STUN server (and equivalent method).

any help would be very much appreciated.

 

[bizsoftware1]

hi, i still cannot overcome this problem and am finding it difficuilt to find the time to invetigate further, does anybody know a good engineer near to milton keynes, uk i could contact??

 

[l33byt1980]

Can you disable everything on your monitor program BAR SIP tracing,
Could you reboot the ip office and try a test call then post the results on here please.

I am uk based and on the results I may be able to help. Could I possibly look at a config?

ACA - IPOffice implement
ACA - IP Telephony
CCNA - Passed at last

 

[l33byt1980]

Right,

Draytel DOES NOT OPERATE stun, I would assume as this uses a session border controller instead. SO we need to disable this, we also need to ensure it routes the UDP 5600 out via NONE, rather than LAN1 or LAN2.

This then uses the IP routes to get to the ITSP address.



ACA - IPOffice implement
ACA - IP Telephony
CCNA - Passed at last

 

[akb1111]

when you try to make a call, what does the phone do or say in the display?.....disconnected or waiting for line.....??? or does it say anything at all?

 

[bizsoftware1]

i do not see any filter settings for sip, can you enlighten me please?

 

[bizsoftware1]

akb1111 i have analogue extentions only on this unit, so no info........ im guessing its waiting for line as nothing happens!

 

[IPOfficeIreland]

and your shortcode is still wrong

="9123@83.170.124.4" callinfop

hey chumpy, how you been?

 

[bizsoftware1]

39079mS CMTARGET: 0.1015.0 3 MasterBedroom.0: TimerExpired cause=CMTCDelayedProcessing
39081mS CMTARGET: 0.1015.0 3 MasterBedroom.0: LOOKUP CALL ROUTE: type=100 called_party=7 sub= calling=202 in=0 complete=0 ses=0
39081mS CMTARGET: OUTGOING CALL ROUTE
39082mS CMTARGET: 0.1015.0 3 MasterBedroom.0: ADD TARGET (N): number=7 type=100 depth=1 nobar=1 setorig=1 ses=0
39083mS CMTARGET: 0.1015.0 3 MasterBedroom.0: FoundKnownSystemTargets 7 (ses: 0)
39084mS CMTARGET: 0.1015.0 3 MasterBedroom.0: SYS SC: 7 2 sc=type=Dial code=7N, num=7N callinfop->sending_complete=0 secondary_dialtone=
39086mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1017.0 -1 BaseEP: NEW CMEndpoint ffd7790c TOTAL NOW=3 CALL_LIST=1
39087mS CMTARGET: 0.1015.0 3 MasterBedroom.0: CancelTimer CMTCDialToneTimeout
39088mS CMTARGET: 0.1015.0 3 MasterBedroom.0: INITIAL TARGETING SUCCEEDED
39088mS CMTARGET: 0.1015.0 3 MasterBedroom.0: GetNoAnswerTimer:15
39090mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1016.0 3 TargetingEP: StateChange: END=B CMCSIdle->CMCSOffering
39091mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1017.0 3 ARS for Draytel: StateChange: END=T CMCSIdle->CMCSOffering
39092mS CMTARGET: TargetOnProgress: res: 1
39093mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1016.0 3 TargetingEP: RequestEnd 0.1017.0 3 ARS for Draytel
39094mS CMTARGET: 0.1015.0 3 MasterBedroom.0: CancelTimer CMTCNoAnswerTimeout
39095mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1017.0 3 ARS for Draytel: StateChange: END=B CMCSOffering->CMCSOverlapRecv
39097mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1018.0 -1 BaseEP: NEW CMEndpoint ffd75bdc TOTAL NOW=4 CALL_LIST=1
39123mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1018.0 3 SIPTrunk Endpoint: StateChange: END=child CMCSIdle->CMCSOffering
39123mS CMTARGET: TargetOnProgress: res: 1
39129mS CMLineTx: v=0
CMSetup
Line: type=NoLine 0 Call: lid=0 id=-1 in=0
Called[] Type=Default (100) Calling[] Type=Unknown (0) Pres=Allowed (0)
HLC: hlc= maint=
LLC: CMTC= CMTM=Circuit CMTR= CMST=Default CMU1=None
BChan: slot=6750208 chan=426477
UUI type= [.] [0x03 ]
Display []
Cause=1, Unallocated (unassigned) number
Timed: 02/01/00 00:192
Locale:


39143mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1016.0 -1 TargetingEP: StateChange: END=X CMCSOffering->CMCSDelete
39144mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1016.0 -1 BaseEP: DELETE CMEndpoint ffd93fbc TOTAL NOW=3 CALL_LIST=1
40003mS CMCallPkt: v=0
CMInformation (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called[] Type=Default (100) Called SubAddress[ddd] Calling[] Type=Unknown (0) Pres=Allowed (0)
HLC: hlc=Telephony maint=
BChan: slot=66048 chan=-1073739264
UUI type=AOC [..] [0x01 0x00 ]
Display []
Cause=20, Subscriber absent (wireless networks)
Timed: 01/136/00 03:03
40555mS CMCallPkt: v=0
CMInformation (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called[] Type=Default (100) Called SubAddress[ddd] Calling[] Type=Unknown (0) Calling SubAddress[¼] Pres=Allowed (0)
lueBC: CMTC=Speech CMTM= CMTR= CMST= CMU1=119, Unrecognised value
lueLLC: CMTC= CMTM= CMTR= CMST=Unstructured CMU1=None
lueBChan: slot=150994944 chan=5300550
lueUUI type= [.]\r..F......@.|....E..|N..|..F.$.....F......A.|.......|..F.....P.F....|p..|...|o>.|b>.|.....\n.........t.\r..........v.J........t...t.[..1/.|.] [0xba 0x5d 0x0d 0x80 0xe5 0x46 0x09 0xff 0xff 0xff 0xff 0xbb ]
lueDisplay [ÿÿ]
lueCause=247,
lueTimed: 136/42/00 65:126
40727mS CMCallPkt: v=0
CMInformation (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called[] Type=Default (100) Called SubAddress[ddd] Calling[] Type=Unknown (0) Calling SubAddress[¼] Pres=Allowed (0)
lueBC: CMTC=Speech CMTM= CMTR= CMST= CMU1=119, Unrecognised value
lueLLC: CMTC= CMTM= CMTR= CMST=Unstructured CMU1=None
lueBChan: slot=150994944 chan=5300550
lueUUI type= [.]\r..F......@.|....E..|N..|..F.$.....F......A.|.......|..F.....P.F....|p..|...|o>.|b>.|.....\n.........t.\r..........v.J........t...t.[..1/.|.] [0xba 0x5d 0x0d 0x80 0xe5 0x46 0x09 0xff 0xff 0xff 0xff 0xbb ]
lueDisplay [ÿÿ]
lueCause=247,
lueTimed: 136/42/00 65:126
41066mS CMCallPkt: v=0
CMInformation (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called[] Type=Default (100) Called SubAddress[ddd] Calling[] Type=Unknown (0) Calling SubAddress[èt] Pres=Allowed (0) Keypad[ú]
lueBC: CMTC= CMTM= CMTR= CMST= CMU1=-60, Unrecognised value
lueHLC: hlc= maint=
lueLLC: CMTC= CMTM= CMTR= CMST=Default CMU1=13, Unrecognised value
lueBChan: slot=46259 chan=1132333236
lueUUI type= [.U..\r.................C~t...4.A~....\r.............C~..............C~......A~........Z.A~....*.A~\r.....C~......................] [0xa0 0x55 0x85 0x00 0x0d 0x00 0x00 0x00 0x14 0x00 0x00 0x00 0xb8 0xfc 0x18]
41416mS CMCallPkt: v=0
CMInformation (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called[] Type=Default (100) Called SubAddress[ddd] Calling[] Type=Unknown (0) Calling SubAddress[èt] Pres=Allowed (0) Keypad[ú]
lueBC: CMTC= CMTM= CMTR= CMST= CMU1=-60, Unrecognised value
lueHLC: hlc= maint=
lueLLC: CMTC= CMTM= CMTR= CMST=Default CMU1=13, Unrecognised value
lueBChan: slot=46259 chan=1132333236
lueUUI type= [.U..\r.................C~t...4.A~....\r.............C~..............C~......A~........Z.A~....*.A~\r.....C~......................] [0xa0 0x55 0x85 0x00 0x0d 0x00 0x00 0x00 0x14 0x00 0x00 0x00 0xb8 0xfc 0x18]
41692mS CMCallPkt: v=0
CMInformation (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called[] Type=Default (100) Called SubAddress[ddd] Calling[] Type=Unknown (0) Calling SubAddress[èt] Pres=Allowed (0) Keypad[ú]
lueBC: CMTC= CMTM= CMTR= CMST= CMU1=-60, Unrecognised value
lueHLC: hlc= maint=
lueLLC: CMTC= CMTM= CMTR= CMST=Default CMU1=13, Unrecognised value
lueBChan: slot=46259 chan=1132333236
lueUUI type= [.U..\r.................C~t...4.A~....\r.............C~..............C~......A~........Z.A~....*.A~\r.....C~......................] [0xa0 0x55 0x85 0x00 0x0d 0x00 0x00 0x00 0x14 0x00 0x00 0x00 0xb8 0xfc 0x18]
41954mS CMCallPkt: v=0
CMInformation (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called[] Type=Default (100) Called SubAddress[ddd] Calling[] Type=Unknown (0) Calling SubAddress[èt] Pres=Allowed (0) Keypad[ú]
lueBC: CMTC= CMTM= CMTR= CMST= CMU1=-60, Unrecognised value
lueHLC: hlc= maint=
lueLLC: CMTC= CMTM= CMTR= CMST=Default CMU1=13, Unrecognised value
lueBChan: slot=46259 chan=1132333236
lueUUI type= [.U..\r.................C~t...4.A~....\r.............C~..............C~......A~........Z.A~....*.A~\r.....C~......................] [0xa0 0x55 0x85 0x00 0x0d 0x00 0x00 0x00 0x14 0x00 0x00 0x00 0xb8 0xfc 0x18]
42351mS CMCallPkt: v=0
CMInformation (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called[] Type=Default (100) Called SubAddress[ddd] Calling[] Type=Unknown (0) Calling SubAddress[èt] Pres=Allowed (0) Keypad[ú]
lueBC: CMTC= CMTM= CMTR= CMST= CMU1=-60, Unrecognised value
lueHLC: hlc= maint=
lueLLC: CMTC= CMTM= CMTR= CMST=Default CMU1=13, Unrecognised value
lueBChan: slot=46259 chan=1132333236
lueUUI type= [.U..\r.................C~t...4.A~....\r.............C~..............C~......A~........Z.A~....*.A~\r.....C~......................] [0xa0 0x55 0x85 0x00 0x0d 0x00 0x00 0x00 0x14 0x00 0x00 0x00 0xb8 0xfc 0x18]
42544mS CMCallPkt: v=0
CMInformation (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called[] Type=Default (100) Called SubAddress[ddd] Calling[] Type=Unknown (0) Calling SubAddress[èt] Pres=Allowed (0) Keypad[ú]
lueBC: CMTC= CMTM= CMTR= CMST= CMU1=-60, Unrecognised value
lueHLC: hlc= maint=
lueLLC: CMTC= CMTM= CMTR= CMST=Default CMU1=13, Unrecognised value
lueBChan: slot=46259 chan=1132333236
lueUUI type= [.U..\r.................C~t...4.A~....\r.............C~..............C~......A~........Z.A~....*.A~\r.....C~......................] [0xa0 0x55 0x85 0x00 0x0d 0x00 0x00 0x00 0x14 0x00 0x00 0x00 0xb8 0xfc 0x18]
42845mS CMCallPkt: v=0
CMInformation (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called[] Type=Default (100) Called SubAddress[ddd] Calling[] Type=Unknown (0) Calling SubAddress[èt] Pres=Allowed (0) Keypad[ú]
lueBC: CMTC= CMTM= CMTR= CMST= CMU1=-60, Unrecognised value
lueHLC: hlc= maint=
lueLLC: CMTC= CMTM= CMTR= CMST=Default CMU1=13, Unrecognised value
lueBChan: slot=46259 chan=1132333236
lueUUI type= [.U..\r.................C~t...4.A~....\r.............C~..............C~......A~........Z.A~....*.A~\r.....C~......................] [0xa0 0x55 0x85 0x00 0x0d 0x00 0x00 0x00 0x14 0x00 0x00 0x00 0xb8 0xfc 0x18]
43018mS CMCallPkt: v=0
CMInformation (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called[] Type=Default (100) Called SubAddress[ddd] Calling[] Type=Unknown (0) Calling SubAddress[èt] Pres=Allowed (0) Keypad[ú]
lueBC: CMTC= CMTM= CMTR= CMST= CMU1=-60, Unrecognised value
lueHLC: hlc= maint=
lueLLC: CMTC= CMTM= CMTR= CMST=Default CMU1=13, Unrecognised value
lueBChan: slot=46259 chan=1132333236
lueUUI type= [.U..\r.................C~t...4.A~....\r.............C~..............C~......A~........Z.A~....*.A~\r.....C~......................] [0xa0 0x55 0x85 0x00 0x0d 0x00 0x00 0x00 0x14 0x00 0x00 0x00 0xb8 0xfc 0x18]
48719mS CMCallPkt: v=0
CMReleaseComp (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called SubAddress[d] Calling[] Type=Unknown (0) Calling SubAddress[èt] Pres=Allowed (0) Keypad[ú]
lueBC: CMTC= CMTM= CMTR= CMST= CMU1=-60, Unrecognised value
lueHLC: hlc= maint=
lueLLC: CMTC= CMTM= CMTR= CMST=Default CMU1=13, Unrecognised value
lueBChan: slot=46259 chan=1132333236
lueUUI type= [.U..\r.................C~t...4.A~....\r.............C~..............C~......A~........Z.A~....*.A~\r.....C~......................] [0xa0 0x55 0x85 0x00 0x0d 0x00 0x00 0x00 0x14 0x00 0x00 0x00 0xb8 0xfc 0x18]
48721mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1015.0 3 MasterBedroom.0: StateChange: END=A CMCSDialling->CMCSCompleted
48731mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1015.0 -1 MasterBedroom.-1: StateChange: END=X CMCSCompleted->CMCSDelete
48739mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1017.0 -1 ARS for Draytel: StateChange: END=X CMCSOverlapRecv->CMCSDelete
48740mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1017.0 -1 BaseEP: DELETE CMEndpoint ffd7790c TOTAL NOW=2 CALL_LIST=0
48740mS CMCallEvt: v= State, new=Idle old=Idle,0,0,END CALL:3
48743mS CMTARGET: 0.1015.0 -1 BaseEP: ~CMTargetHandler

 

[bizsoftware1]

theproviderpatched - how can i email you the config??

 

[l33byt1980]

email a config to l33 byt at o2 dot co dot uk
Remove ALL spaces.

You need to enable development tracing and then go onto the SIP tab and enable all of those. Every thing else needs disabling.
let me know when you have emailed config.

ACA - IPOffice implement
ACA - IP Telephony
CCNA - Passed at last

 

[IPOfficeIreland]

there's not 1 sip trace in that thread

 

[telepaul]

Works nicely over here!

You need minimum one sip license and VCM installed.



Network Topology Settings
*************************
Firewall/NAT Type = unknown
Public IP Address = your public IP
Public Port = 5060
Run STUN on startup = OFF
Do not use stun!

Setup siptrunk
**************
ITSP Domain Name:= draytel.org
ITSP IP Address:= 217.14.132.183
Primary Authentication Name= username 8xxxxxxx
Primary Authentication Password:= password xxxxxxx
Primary Registration Expiry = 20

Registration Required = on
In Service = on
RE-INVITE Supported = on

SIP URI
*******
Incoming Group ID= 30
Outgoing Group ID= 30

Network Configuration
*********************
Layer 4 Protocol = UDP
Use Network Topology Info = none
Send Port = 5060
Listen Port = 5060

Short code
**********
Short Code: 0N;
Feature: dial
Telephone Number: 0N”@draytel.org”
Line Group ID: 30 (or ARS 50)

 

[bizsoftware1]

********** Warning: Logging to Screen Started **********

282416mS CMCallPkt: v=0
CMSetup (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called SubAddress[d] Calling[] Type=Unknown (0) Calling SubAddress[?²H] Pres=Allowed (0) Keypad[‘|N ‘|ìáC]
lueBC: CMTC= CMTM=Circuit CMTR= CMST=Default CMU1=-40, Unrecognised value
lueHLC: hlc= maint=
lueBChan: slot=134348800 chan=-1242497024
lueUUI type= [.....t..9...........L........t...t.\..1/.|.W......3d........9..............c..P........\..................A1C~.......@................;5C~..] [0x18 0x00 0xd8 0xba 0xe8 0x74 0xe2 0x04 0x39 0x00 0x84 0x00 ]
282417mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1012.0 -1 BaseEP: NEW CMEndpoint ffd966cc TOTAL NOW=1 CALL_LIST=0
282418mS CMCallEvt: v= State, new=Idle old=Idle,0,0,CREATE CALL:2
282418mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1013.0 -1 BaseEP: NEW CMEndpoint ffd954e8 TOTAL NOW=2 CALL_LIST=0
282426mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1012.0 2 MasterBedroom.0: StateChange: END=A CMCSIdle->CMCSDialInitiated
282428mS CMTARGET: 0.1012.0 2 MasterBedroom.0: LOOKUP CALL ROUTE: type=100 called_party= sub= calling=202 in=0 complete=0 ses=0
282428mS CMTARGET: OUTGOING CALL ROUTE
282429mS CMTARGET: 0.1012.0 2 MasterBedroom.0: ADD TARGET (N): number= type=100 depth=1 nobar=1 setorig=1 ses=0
282430mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1012.0 2 MasterBedroom.0: StateChange: END=A CMCSDialInitiated->CMCSDialling
285507mS CMCallPkt: v=0
CMInformation (Secondary)
Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0
Called[] Type=Default (100) Called SubAddress[ddd] Calling[] Type=Unknown (0) Calling SubAddress[ètÂåtâ9] Pres=Allowed (0) Keypad[ú]
HLC: hlc= maint=
Display [åtÍ«ºÜ]
286510mS CMTARGET: 0.1012.0 2 MasterBedroom.0: TimerExpired cause=CMTCDelayedProcessing
286511mS CMTARGET: 0.1012.0 2 MasterBedroom.0: LOOKUP CALL ROUTE: type=100 called_party=7 sub= calling=202 in=0 complete=0 ses=0
286512mS CMTARGET: OUTGOING CALL ROUTE
286512mS CMTARGET: 0.1012.0 2 MasterBedroom.0: ADD TARGET (N): number=7 type=100 depth=1 nobar=1 setorig=1 ses=0
286513mS CMTARGET: 0.1012.0 2 MasterBedroom.0: FoundKnownSystemTargets 7 (ses: 0)
286514mS CMTARGET: 0.1012.0 2 MasterBedroom.0: SYS SC: 7 2 sc=type=Dial code=7N, num=7N callinfop->sending_complete=0 secondary_dialtone=
286516mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1014.0 -1 BaseEP: NEW CMEndpoint ffd7a48c TOTAL NOW=3 CALL_LIST=1
286517mS CMTARGET: 0.1012.0 2 MasterBedroom.0: CancelTimer CMTCDialToneTimeout
286517mS CMTARGET: 0.1012.0 2 MasterBedroom.0: INITIAL TARGETING SUCCEEDED
286518mS CMTARGET: 0.1012.0 2 MasterBedroom.0: GetNoAnswerTimer:15
286519mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1013.0 2 TargetingEP: StateChange: END=B CMCSIdle->CMCSOffering
286521mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1014.0 2 ARS for Draytel: StateChange: END=T CMCSIdle->CMCSOffering
286521mS CMTARGET: TargetOnProgress: res: 1
286522mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1013.0 2 TargetingEP: RequestEnd 0.1014.0 2 ARS for Draytel
286522mS CMTARGET: 0.1012.0 2 MasterBedroom.0: CancelTimer CMTCNoAnswerTimeout
286523mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1014.0 2 ARS for Draytel: StateChange: END=B CMCSOffering->CMCSOverlapRecv
286525mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1015.0 -1 BaseEP: NEW CMEndpoint ffd79458 TOTAL NOW=4 CALL_LIST=1
286532mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1015.0 2 SIPTrunk Endpoint: StateChange: END=child CMCSIdle->CMCSOffering
286533mS CMTARGET: TargetOnProgress: res: 1
286539mS CMLineTx: v=0
CMSetup
Line: type=NoLine 0 Call: lid=0 id=-1 in=0
Called[] Type=Default (100) Calling[] Type=Unknown (0) Pres=Allowed (0)
HLC: hlc= maint=
LLC: CMTC= CMTM=Circuit CMTR= CMST=Default CMU1=None
BChan: slot=6750208 chan=426477
UUI type= [.] [0x03 ]
Display []
Cause=1, Unallocated (unassigned) number
Timed: 02/01/00 00:192
Locale:


286552mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1013.0 -1 TargetingEP: StateChange: END=X CMCSOffering->CMCSDelete
286552mS CMCallEvt: v= State, new=Idle old=Idle,0,0,0.1013.0 -1 BaseEP: DELETE CMEndpoint ffd954e8 TOTAL NOW=3 CALL_LIST=1

********** Warning: Logging to Screen Stopped **********

does this help? what does the unallocated unassigned number mean?

 

[IPOfficeIreland]

still no sip trace. you can't diagnose a sip problem without a trace.

do you know how to do this bizsoftwareman?

 

[bizsoftware1]

lol no, im strugling to find the settings in monitor, im using version 4.1(15)
I have turned on development logging, and then selected all items under H323.

I appreciate some direction!

 

[l33byt1980]

There is a SIP tab on monitor.


ACA - IPOffice implement
ACA - IP Telephony
CCNA - Passed at last

 

[tlpeter]

It is next to the system tab !


ACA - Implement IP Office
ACS - Implement IP Office
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!

 

[bizsoftware1]

Not on mine, i have snmp and T1 either side of system tab, im using version 4.1(15)

 

[l33byt1980]

Then either your IP office is on the wrong software or you are using the wrong monitor program.

ACA - IPOffice implement
ACA - IP Telephony
CCNA - Passed at last

 

[tlpeter]

If i use monitor then it says 6.2.4 that belongs to 4.2
So you are using a 2.1 verison or do you really using the 4.1.15 version ?


ACA - Implement IP Office
ACS - Implement IP Office
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!