CLID not being passed over q931 circuits

[GANDERUK]

Hi Guys

Recently upgraded option 61c from 25.15 to 4.5.
All is fine apart from an issue with CLID,
A call is made into the switchboard on the upgraded 61c the clid (ie my mobile no. is shown on the console display, if the call is then transfered over a Q931 circuit to another option 61c all that is shown on the display at the remote site is the route/trunk info. (If the call is transferred from the switch to a local extn on that switch the CLID is passed ok)
nb it used to work prior to the upgrade .

Any ideas appreciated

 

[johnpoole]

post the route that is dropping the clid

john poole
bellsouth business
columbia,sc

 

[GANDERUK]

Here you go John

Cheers

Dave

ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 5

TYPE RDB
CUST 00
ROUT 5
DES
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
IDEF NET
RCLS INT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC SL1
PNI 00701
NCNA YES
NCRD YES
TRO NO
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB NO
STEP
ACOD 1505
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
SIGO ESN5
MFC NO
ICIS YES
OGIS YES
TIMR ICF 1920
OGF 1920
EOD 13952
LCT 256
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3


PAGE 002

PRPS 800
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DRNG NO
CDR YES
INC YES
LAST NO
TTA YES
ABAN NO
CDRB NO
QREC NO
OAL YES
AIA YES
OAN YES
OPD YES
NDP EXC 0
CDRX NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 7
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 0
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 1505 5
SGRP 0
ARDN NO
AACR NO

 

[911guru]

Do you have the current DepList installed?

911Guru

http://pbx-e911.com

 

[GANDERUK]

Hi DEP lists are installed. I found the problem. The DASS Routes had LID set to 0 ie not sending CLID. Changed LID to 1 so now i/c calls on the DASS routes now pass the CLID over onto the Q931 Circuits. As part of the upgrade the NTAK35 DASS/DDSL cards had to be changed for NT6D11 DCHI cards. The original cards had no interaction with the LID prompt so the CLID was just sent anyway (even though LID was set to 0.(not to pass CLID) However the later NT6D11 cards did interact with the LID prompt hence stopping the CLID being passed.
Many thanks for your help anyway