Changing Local lines (E1) to ISDN PRI

[ONsiteengineer]

Hi,

I want to change my trunk from my local line E1 to Isdn pri. What particular changes I need to do? If you can give me steps it would be a good help. Thanks a lot.

 

[inerguard]

add DS1 first, then signalling group next, followed by the trunk group. Whatever trunk group number you use, try to keep the signalling group the same, e.g. Trunk 10, use signalling group 10.

The example below is for group 8

The DS1 setup (assuming your in Europe) is as follows: -

Location: 05A10 Name: MDI Trunk 1
Bit Rate: 2.048 Line Coding: hdb3

Signaling Mode: isdn-pri
Connect: network
TN-C7 Long Timers? n Country Protocol: etsi
Interworking Message: PROGress Protocol Version: a
Interface Companding: alaw CRC? y
Idle Code: 01010100
DCP/Analog Bearer Capability: 3.1kHz

T303 Timer(sec): 4


Slip Detection? n Near-end CSU Type: other


The Signalling Group setup is a s follow:-


Group Number: 8 Group Type: isdn-pri
Associated Signaling? y Max number of NCA TSC: 0
Primary D-Channel: 05A1016 Max number of CA TSC: 0
Trunk Group for NCA TSC: 8
Trunk Group for Channel Selection: 8 X-Mobility/Wireless Type: NONE
TSC Supplementary Service Protocol: a Network Call Transfer? n


When you first set up the signalling group you will need to leave "Trunk Group for Channel Selection" blank until you set up the trunk group. When the trunk group is set up come back and enter the trunk group number in this field.



Group Number: 8 Group Type: isdn CDR Reports: y
Group Name: MDI Incoming Trunk PRI 1 COR: 90 TN: 1 TAC: 708
Direction: two-way Outgoing Display? n Carrier Medium: PRI/BRI
Dial Access? n Busy Threshold: 255 Night Service:
Queue Length: 0
Service Type: public-ntwrk Auth Code? n TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4
Group Type: isdn

TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): enbloc/enbloc

Trunk Hunt: cyclical
Digital Loss Group: 13
Incoming Calling Number - Delete: Insert: Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? y
Answer Supervision Timeout: 0
Administer Timers? n
TRUNK FEATURES
ACA Assignment? n Measured: both Wideband Support? n
Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: y Send Calling Number: y
Used for DCS? n Send EMU Visitor CPN? n
Suppress # Outpulsing? n Format: public
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider

Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: y
Network Call Redirection: none Hold/Unhold Notifications? n
Send UUI IE? y Modify Tandem Calling Number? n
Send UCID? n
Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation? n

Apply Local Ringback? n US NI Delayed Calling Name Update? n
Show ANSWERED BY on Display? y
Network (Japan) Needs Connect Before Disconnect? n

SBS? n


QSIG Value-Added? n


1: 05A1001 TN2464 8
2: 05A1002 TN2464 8
3: 05A1003 TN2464 8
4: 05A1004 TN2464 8
5: 05A1005 TN2464 8
6: 05A1006 TN2464 8
7: 05A1007 TN2464 8
8: 05A1008 TN2464 8
9: 05A1009 TN2464 8
10: 05A1010 TN2464 8
11: 05A1011 TN2464 8
12: 05A1012 TN2464 8
13: 05A1013 TN2464 8
14: 05A1014 TN2464 8
15: 05A1015 TN2464 8

16: 05A1017 TN2464 8
17: 05A1018 TN2464 8
18: 05A1019 TN2464 8
19: 05A1020 TN2464 8
20: 05A1021 TN2464 8
21: 05A1022 TN2464 8
22: 05A1023 TN2464 8
23: 05A1024 TN2464 8
24: 05A1025 TN2464 8
25: 05A1026 TN2464 8
26: 05A1027 TN2464 8
27: 05A1028 TN2464 8
28: 05A1029 TN2464 8
29: 05A1030 TN2464 8
30: 05A1031 TN2464 8

Enjoy...


[Started on Version 3 software 15 years a go]

 

[Lostpbx]

Can you set all this up before the local phone company does the cutover or do you have to wait and do it all at the same time? My goal is to do all the programing first then have AT&T do their cut so I can minimize down time.

 

[AvayaTier3]

AT&T and E1 is not something that is normal in the U.S.
Are you sure you are going to have E1?

It's a good idea to set all this up ahead of time, then move the facility to the new ds1 board at cut time.

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

35 years Bell, AT&T, Lucent, Avaya
Tier 3 for 25 years and counting

http://bshtele.com

 

[Lostpbx]

No I don't have E-1 just analog lines. I just was curious how much of the programing I can do before the cutover.

 

[AvayaTier3]

What hardware platform? What cm software version?

You need to check customer options and make sure you can add isdn. If you can, you can program the ds1, the trunk-group, the signaling group, then add the trunks.. This can all be done ahead of time.

No service will be affected. You will only have a ds1 alarm.

display system-parameters customer-options Page 3 of 7 SPE B
OPTIONAL FEATURES
ISDN-PRI? y

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

35 years Bell, AT&T, Lucent, Avaya
Tier 3 for 25 years and counting

http://bshtele.com

 

[Lostpbx]

I have a g3r v9 4 cabinets linked at the main site and 5 other sites all with g3 cabinets. They all dial out from the main location.

ISDN-PRI = Y.

 

[4merAvaya]

This thread was started by ONsiteengineer. The last question was asked by Lostpbx. Are you the same person or are there 2 different questions?

Kevin

 

[ONsiteengineer]

Hi,

Lostpbx, you need to have new thread for your concern.

Thanks a lot for the replies. I will do this after the cutoff from the telco since I will use same media module (mm711 for my isdn-pri). I have g700/s8300). Do ineed to change something in my incoming and outgoing numbering plans? THanks a lot.

 

[ONsiteengineer]

I mean mm710 media module..

 

[inerguard]

Hi,

My answer was based on setting up an ISDN Circuit in Europe where E1 is used. T1 is used in the USA etc. just to clariffy that.


[Started on Version 3 software 15 years a go]

 

[audra87]

Is there a way i could have my local lines routing to the PRI is they go down as a backup??

 

[ONsiteengineer]

Do i need to add DS1 if i have G700/S8300?

 

[Lostpbx]

Sorry for the piggy-backing, I thought some of my questions might help out as I am doing the same thing. I will start a new thread.